Manual setup Presetting channels | Sony SLV-AV100UX guide

Manual setup — Presetting channels

If some channels could not be preset using EASY SET UP, you can preset them manually.

Before you start…

•Press VHS TUNER.

–If the TV doesn’t turn on, turn it on manually.

Press VHS TUNER again if connected with a EURO-AV (Scart) cable.

–If connected with a EURO-AV (Scart) cable, the TV is automatically set to VCR reception.

–If connected with only the antenna cable, set the TV to the VCR’s programme position manually.

Getting Started

MENU

1

EXECUTE

CURSOR

> / . / ? / /

PROG +/–

2

Lift the top cover of the remote commander.

Press MENU. Then press CURSOR >/. to move the cursor (I) to VHS MENU, and press EXECUTE.

VHS MENU

T I MER SET / CHECK

SET UP MENU

TUNER PRESET

SET UP CH & VIDEO Plus+

CLOCK SET

SELECT	:
SET	:	EXECUTE
EXIT	:	MENU

Press CURSOR >/. to move the cursor (I) to TUNER PRESET and press EXECUTE.

TUNER PRESET	PROG10

CHANNEL SET	2 1
AFT	ON	OFF
FINE TUNING

SELECT :

SET :

Note

•The menu disappears automatically if you don’t proceed within a few minutes.

3

4

Press CURSOR >/. to move the cursor (I) to CHANNEL SET.

TUNER PRESET	PROG10

CHANNEL SET	2 1
AFT	ON	OFF
FINE TUNING

SELECT :

SET :

Press PROG +/– to select the programme position.

Selected programme position

TUNER PRESET			PROG4
CHANNEL SET		2 1
AFT		ON	OFF
FINE TUNING
SELECT	:
SET	:

continued

Getting Started

19

Image 19

Sony SLV-AV100UX operating instructions Manual setup Presetting channels, Before you start…

Contents

Amplifier Integrated Video Cassette Recorder Compatible colour systems PrecautionsSafety Installing Table of contents Step Inserting the batteries Using the remote commanderGetting Started Disconnect the aerial cable from your Aerial input on your TV usingUnit and the EURO-AV Scart connector On the TV Before you connect If your TV doesn’t have a EURO-AV Scart connector Connecting speaker systems Placing the speakers Connecting an active wooferListening through the headphones Speakers Rear L/R connectors Connecting various audio/video equipment Connect the mains lead to the mains Supplied Conserving power while the unit is standing by Turn on your TV and select a programme position To check that the TV tuning is correctPress ON/STANDBY to turn on the unit Press RF Channel on the unit Press VHS Tuner to turn on the unit and TV Press Easy SET UP on the unitSet the TV for VCR reception Programme positions. If all the settings are Lift the top cover of the remote commanderPreset automatically, change the programme Positions of the stations, and disable the unused Press ?// to select the centre mode Setting up the unit with Easy SET UP Equal volume balance with the other speakers at Decrease the volume of the centre speaker so youHave an equal volume balance with the other Volume of the rear speakers so you have an If you have only front and centre speakers If you have only front and rear speakers Before you start… Manual setup Presetting channels Manual setup Presetting channels If the picture is not clear Disabling unwanted programme positions Manual setup Selecting station names/setting up Video Plus+ Press Cursor / to highlight the guide channel column only Guide Station name Channel Setting up Video Plus+ for satellite broadcasts Changing programme positions Manual setup -- Changing/disabling programme positions ITV BBC1 BBC2 CH4 Select Manual setup -- Changing/ disabling programme positions Setting the clock manually Manual setup Setting the clock Manual setup Setting the clock Changing the station for Auto Clock Set Basic VCR Operations Playing a video tape To change the information in the display window To use the time counterTo mute the sound Fields Using the pre- programmed sound To watch another TV programme while recording Recording TV programmesPress r REC to start recording To stop recording To check the remaining tape length To save a recording Recording TV programmes Recording TV programmes using Video Plus+ To record satellite broadcasts Recording TV programmes using Video Plus+ Using the unit after setting the timer Setting the timer manually Daily/weekly recording Timer recording with PDC signalsPress Cursor / to confirm the setting Press Execute Press Timer REC ON/OFF Checking/changing/ cancelling timer settings When the timer settings overlap Audio/Video Equipment Operations Selecting the equipmentControlling the function buttons Before operating audio/video equipment Watching a picture while listening to audio equipmentFunction buttons on the unit Function To turn off the whole system To increase or decrease the volume Controlling VCRs Controlling VCRs which have the Command Mode selectorTurning on and controlling the unit’s VCR Turning off the selected VCR Using the remote commander buttons to control the other VCRTo relate VIDEO1 or VIDEO2 with Command Mode again Controlling VCRs Turning on and controlling another VCR Controlling the TV Turning off the TV Controlling the TV Using the TV independentlyTo select the TV’s input source Listening to a radio programme Listening to preset radio programmesTo scan preset stations To scan the preset stations To locate a track with the number buttons Playing back a CD Playing a tape Controlling a cassette deckRecording on a tape Controlling a cassette deck Controlling a DAT deck Customizing the remote commander for a DAT deck Controlling a DAT deck Controlling an MD deck Customizing the remote commander for an MD deckPlaying an MD Recording on an MD Controlling an MD deck To start playback from the beginning of either LD side Customizing the remote commander for an LD playerControlling an LD player Playing back an LD Turning off the LD player Controlling an LD player To temporarily turn off the sound effect you set Taking advantage of the sound fieldsSound Field Operations Selecting the sound field What’s Dolby Surround and Dolby Pro Logic Surround? Taking advantage of the sound fieldsWhat’s surround sound? Getting the most out of Dolby Pro Logic Surround sound Adjusting the delay time Customizing the sound fields Press Cursor /. to move the cursor I to Tone Edit Adjusting the tone for all sound fieldsTo start your adjustment from a flat equalizer curve To return to the previous menu Press EXECUTE, then press Cursor Start playing a programmeSource, then repeat steps Highlight Effect Reinforcing the bass sound for all sound fields Source, then repeat steps Through 4 in Using the preSound fields in step Reconfiguring the Prologic and Theatre sound fields Increasing the maximum rear speaker level Playing/searching at various speeds Using the Click Shuttle ringAdvanced VCR Operations To extend the duration Recording TV programmes using the quick timer Nicam system Recording stereo and bilingual programmesTo select the sound while recording How sound is recorded on a video tape To stop searching Searching using the index function Adjusting the tracking Adjusting the pictureAbout Optimum Picture Control OPC Menu choices Changing menu options Editing Recording from another VCR or LD playerBefore you start editing Before you start dubbing… Audio dubbing To listen to both the hi-fi and normal audio To stop while editing Factory set functions Customizing the remote commander function buttonsTo restore the factory settings for VIDEO1 or VIDEO2 Additional Information Symptoms caused by contaminated video heads Troubleshooting Troubleshooting Remote commander does System Amplifier General SpecificationsVCR Inputs and outputs Front panel Index to parts and controls Front panel, with cover opened Display window Rear panel Index to parts and controls Remote commander Remote commander, with top cover opened Y, Z Index