User’s Guide Wireless Print Server Requirements | Sony SX-215

User’s Guide

Wireless Print Server Requirements

To print using the SX-215 wireless print server, you will need an 802.11b or 802.11g wireless network consisting of either of the following:

An 802.11b or 802.11g wireless-enabled PC or Macintosh printing straight to the printer (Ad-Hoc or Peer-to-Peer Mode).

An 802.11b or 802.11g wireless access point that allows wireless and wired Ethernet- enabled computers to print to the wireless print server.

To configure and print to the wireless print server, you will need the following information from your wireless network administrator:

Wireless Mode used (Infrastructure or Ad-Hoc)

The SSID (service set identifier) for your wireless network.

If you are using TCP/IP (recommended for Windows Networks) and are not connected to a DHCP server (for obtaining an IP Address automatically), you will need a unique IP Address for the wireless print server (for example: 192.168.1.14). If the wireless print server is not on the same IP subnet as the computers you are printing from, you will also need a subnet mask and a router (default gateway) address.

Wireless security settings

Document #40181-420 Rev. B

9

Image 9

Sony SX-215 user manual User’s Guide Wireless Print Server Requirements

Contents

User’s Guide SX-200/SX-215 User’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Product Overview Introduction Package Contents User’s Guide About This User’s Guide Windows System RequirementsOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components Label Color State Status LED Indicators Default Settings wired and wireless print servers Factory Default SettingsWireless Default Settings wireless print servers only Pushbutton Functions Before You Begin Hardware Installation User’s Guide User’s Guide Verifying the Connection to the Printer Configuration Options Configuration and ManagementExtendView Utility Web Browser Interface Configuration Console HP Web JetAdmin Utility Document #40181-420 Rev. B User’s Guide Telnet Adding the Standard TCP/IP Port User’s Guide Windows Print Queue Configuration Select the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Troubleshooting Printing ProblemsIntroduction Checking the Network Connection and Cabling Troubleshooting Windows Problems User’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Information for United States Users SX-200 Appendix a Safety and Regulatory Notices Information for Canadian Users IC notice SX-200 User’s Guide Declaration of Conformity FCC SX-200 Declaration of Conformity CE SX-200 User’s Guide Information for European Users SX-200 Information for Canadian Users IC Notice SX-215 User’s Guide Declaration of Conformity FCC SX-215 User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X User’s Guide Command console access information Telnet Command Console AccessSerial Port Command Console Access SH NW Network CommandsSH NW Auth SET NW ENC SH NW ENC SH NW ModeSET NW KEY# SET NW Keyval SH NW Speed CL NW BSsid SET NW Certcn SH NW StatsSH NW Certcn SET NW CERTCN2 SET NW Certexp SH NW CERTCN2SH NW Certexp SET NW Certkey SET NW Inap SET NW PWSH NW Inap SET NW Realm SET NW Wpapsk SH NW WpagroupSET NW Wpatrace SET NW Iroam SET NW DFS SH NW IroamSH NW DFS SET NW REGDOMain SET NW Wired Port CommandsSH NW REGDOMain Sets Ethernet Speed to 10baseT, 100baseTX, or Autosense User’s Guide Enable or disable bidirectional mode User’s Guide Parallel Port CommandsSET Port P1 BIDir Shows Port parameters Sample output SET Port P1 Nbuf ENable DIsable Enable or disable PJL status initializationCL Port port JOB USB Port Commands Server Information CommandsSET SERVEr DEscription SET SERVEr NAme SET Snmp SETCOMM1 SET Snmp SETCOMM2SH Serial SH SERVEr COunters User’s Guide SH SERVErSH Snmp SH VErsion SET Servi service name BOT Service CommandsSET Servi service name EOT SET Servi service name FIlter SET Servi service name FRS SET Servi service name FMSSET Servi service name IP SET Servi service name NAme SH Servi PRI servicenum User’s Guide SET Servi service name PRIoritySET Servi service name RECeive SET Servi service name TCP TCP/IP Commands String Commands SH IP ACcess User’s Guide SET IP ACcessSET IP ARP ENable SET IP RANge SET IP Chksum SET IP FTPSET IP Http SET IP LPD SET IP Tftp SET IP TCP Shows TCP/IP related Parameters Sample output SH IP Firmware Update User’s Guide SH LOAd Shows the firmware update parameters Sample output SET Default Other CommandsExit SH Free SH Poweron SET PoweronInit Save Unprotect Netware Commands SET Netw QServer User’s Guide SET Netw POllingSET Netw REscan SET Netw SErver Email Printing Commands SET POP3 TImeout SET POP3 PAsswordSET Smtp ENable SET Smtp ADdress SET DLC ENable DLC / Netbeui CommandsSET DLC TIMeout SH POP3 SH DLC Appletalk Commands SET APPletalk ZOne Configures the Appletalk Zone for this server ExtendView Wireless Security Configuration Key Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk