Manuals / Star Micronics / Computer Equipment / Printer

Star Micronics CBM-820 manual Example When selecting the 5 ⋅ 7 font p1 p2 p3 p4 p5 p6 MSB

Models: CBM-820

1 132

Download 132 pages 45.64 Kb

Page 59

[Example]

[Example]

• When selecting the 5 ⋅ 7 font

p1 p2 p3 p4 p5 p6

MSB

LSB

When deﬁning the pattern above to the code 20H

ESC

&

y

c1

c2

x

p1

p2

p3

p4

p5

Code (hex.) 1B

26

01

20

20

05

3E

48

88

48

3E

• When selecting the 7 ⋅ 7 font

p1

p2

p3

p4

p5

p6

p7

p8

p9

p10

MSB

LSB

When deﬁning the pattern above to the code 20H

ESC

&

y

c1

c2

x

p1

p2

p3

p4

p5

p6

p7

Code (hex.) 1B

26

01

20

20

07

1E

20

48

80

48

20

1E

– 48 –

Image 59

Star Micronics CBM-820 manual Example When selecting the 5 ⋅ 7 font p1 p2 p3 p4 p5 p6 MSB

Contents

Page Declaration of Conformity IMPORTANT SAFETY INSTRUCTIONS WICHTIGE SICHERHEITSANWEISUNGEN Pour L’utilisateurs Canadiens CAUTION Use shielded cable for this equipment SicherheitshinweisFor Uses in Canada CAUTIONS BE SURE TO OBSERVE SAFETY PRECAUTIONSDo not connect/disconnect the AC adapter with wet hands PRECAUTIONS FOR INSTALLATION To Prevent Injury and Spreading of Damage PRECAUTIONS FOR HANDLINGDAILY MAINTENANCE 1.1 Choosing a place for the printer 1. Printer SetupFerrite core Fastener AC Cable 1.2 Unpacking the printerPrinter Ribbon cassette User’s Manualtape tape 1.3 Removing the protective materialsGeneral Speciﬁcations Speciﬁcations2.3 Paper Speciﬁcations and Print Area 2.2 Printing SpeciﬁcationsPaper feed Adjustable in n/60″ units approximatePrint Position Paper Feed2.4 Power Supply Speciﬁcations 3.1 General guide 3. Outer Appearance and Component Parts4.1 Removing the printer cover 4.2 Installing the ribbon cassette4. Operation Replace the printer cover Rotate the knob on the cassette again to take up any slack4.3 Removing the ribbon cassette 4.4 Connecting to a power outlet and turning power on and offPlug the other end of the power cord to a standard household wall outlet Ferrite core 28 mm diameter Cable Interface 4.5 Connecting to your host computerPass the fastener through the ferrite core 4.6 Connecting to a peripheral unit 4.7 Inserting the paper into the printer At least 3 cm Print start position mark 4.8 AutoSide LoadingSend data from your host computer to be printed on the paper PAPER OUT 4.9.1 Indicator lightsPOWER 4.9 Control Panel Operations4.9.3 Producing a test print 4.9.4 Adjusting the dot alignmentThis is caused when mechanical parts of the printer get out of alignment. This happens only rarely and you may never experience it at all throughout the life of the printer. If you do have problems, use the following procedure to correct it 4.9.5 Hexadecimal dump 3 Data Receive Error 4.9.6 Errors1 Recoverable Errors 2 Non-recoverable Errors4.10 Paper Sensors Page ON OFF See table below 5.2 Available DIP switch settingsSwitch 0000 5.3 Memory Switch SettingsThe table below shows the factory settings for the memory switches Memory Switch6. Interface 6.1 Pins and Signal NamesD-sub 25 pin 6.2 Interface Connections7.1 Modular plug 7. Peripheral Unit Driver Circuit7.2 Drive circuit Other Areas 8. Maintenance and ServiceNorth America 9. Print Control Functions 9.1 List of ESC/POS CommandsEnables/Disables Automatic Status Sending Enabled Line Enabled only at the head of the lineSet Only setting is enabled Only part of setting is enabled ¢ Ignores partially Disabled An argument is processed as next data9.2.1 Description of Each Items 9.2 Command DetailsXXXX 9.2.2 Command Details Page Mode Standard Modesequence of 10H04Hn 1 n DLE EOT nDecimal DescriptionDecimal DescriptionESC u, ESC v, GS a, 6. Interface DescriptionDecimal Descriptionset print area ESC SP nESC ! n Ignores ESC #Sets Memory Switch MSW5-C ESC “q” Command FunctionDescription MSW5-D1B, the command selects the download character set ESC % nESC & y c1 c2 xdyxxc2-c1+1 Example When selecting the 5 ⋅ 7 font p1 p2 p3 p4 p5 p6 MSB Vertical Direction ESC * m nL nH dkMode 7 6 5 4 3 2 1 Bit Image Data High Low Print Data follows ESC 3 nESC = n Initializes Printer ESC @ESC C n ESC D nk NUL Decimal ESC F nESC J n 1B, the command selects reverse directional ejectionESC K n FF, 6. Interface ESC LThis command switches from the standard mode to the page mode Japan ESC R nU.S.A SpainB ¤ ¤ ¤ ¤ ¤ ¤ ¤ ESC T ndy = dyL + dyH ⋅ ESC W xL xH yL yH dxL dxH dyL dyHESC c 4 n ESC d n ESC c 5 nESC f t1 t2 ESC e nm = 0, 1, 48 ESC p m t1 t2Generates Speciﬁed Pulses Memory Switch ESC qSelects Character Code Table ESC t nwill send only 1 byte without conﬁrming the DSR signal status ESC u nGS a, 2.3 Paper Speciﬁcations and Print Area This command sends the status of the paper sensor when it is executedESC n Description GS I nGS a n Feeding the paper by the Paper Feed switch Drawer kick connector No. 3 pin status = LDrawer kick connector No. 3 pin status = H The bits 5 and 6 of the 3rd byte will be turned to 1 no paper and Sends Status GS r nSends the status of the drawer kick connector. Same as ESC u Status 1.1 Codepage PC437 USA, European Standard 1. Character Codes Table1.2 Codepage Katakana Japanese 1.3 Codepage PC850 Multilingual 1.4 Codepage PC860 Portuguese 1.5 Codepage PC863 Canadian-French 1.6 Codepage PC865 Nordic 1.7 Codepage PC852 Eastern Europe 1.8 Codepage PC866 Russian 1.9 Codepage PC857 Turkish 1.10 Windows Codepage 1.11 Codepage PC858 Multilingual Dimensions and Weight Appendix 1 Outline Drawing of Printer CBM-8201500 +100 Appendix 2 Outline Drawing of AC Adapter 31ADUnit mm AC ADAPTER1.1 Wahl eines Aufstellungsorts für den Drucker 1. Drucker-EinrichtungHinweis 1.2 Auspacken des DruckersKlebeband Klebeband 1.3 Entfernen der SchutzmaterialienTechnische Daten Allgemeine DatenWichtig Zeichenmatrix 2.2 DruckspeziﬁkationenPapier-Speziﬁkationen und Druckbereich Zeichensatzfixiert WichtigPapiervorschubrichtung Letzte DruckzeileEine Gleichspannungsquelle von 24 V ±5% und mehr als 1,9 A verwenden 2.4 Technische Daten zur NetzversorgungWichtig 3.1 Allgemeine Anleitung 3. Außenansicht und Bauteile4.2 Einsetzen der Farbbandkassette 4. Betrieb4.1 Abnehmen der Druckerabdeckung Die Abdeckung aufsetzen Hinweis 4.3 Entnehmen der FarbbandkassetteWichtig Den anderen Stecker des Netzkabels an eine Netzsteckdose anschließenWichtig 4.5 Anschließen an den HostcomputerFühren Sie den Kabelbinder durch den Ferritkern Wichtig 4.6 Anschluß an ein PeripheriegerätWichtig 4.7 Papier in den Drucker einlegenWichtig 4.8 Automatischer Papiereinzug AutoSide LoadingWichtig Page PAPER OUT 4.9 Bedienfeld4.9.1 Anzeigeleuchten POWERFORWARD REVERSE RELEASE 4.9.2 TastenSchalten Sie den Drucker ein und legen Sie ein Blatt Papier ein Hinweis 4.9.5 Sedezimaler DatenausdruckHinweis 3 Datenempfangsfehler 4.9.6 FehlerBehebbare Fehler Nicht behebbare Fehler4.10 Papiersensoren 5.1 Zugang zu den DIP-Schaltern 5. DIP-SchaltereinstellungDie Druckerabdeckung wieder ansetzen HinweisHinweis 5.2 Verwendbare DIP-Schaltereinstellungen Wichtig 5.3 Einstellen der Speicherschalter6. Schnittstelle Stifte und Signalnamen6.2 Schnittstellenanschlüsse Wichtig 7. Treiberschaltung für periphere Einheiten7.1 Modularstecker Hinweis 7.2 TreiberschaltungAndere Gebiete 8. Wartung und DienstNordamerika