GH Controller Menu Structure | Sterling 882.00722.00 manual

“Recipe” Page (Start)

¾Extruder RPM is displayed

¾Extruder throughput is displayed

¾Line Speed is displayed (GH Full Control with Line speed option Only)

¾Weight Per Length, Weight Per Area, or simple throughput is displayed on GH Full Control versions depending on setup parameters

¾GH-F Target throughput and percent is displayed (GH-F Only)

¾Access “Inventory” Page

¾Access “Setup” Page

¾“Next” to access “Inventory” page.

GH Controller Menu Structure

“Inventory” page

¾Clear Inventory

¾Manual Control

¾“Next” returns to “Recipe” page

“Manual Control” Page

¾Reload ON/OFF

¾Return to the “Inventory” Page

“Setup” Page

¾Touch the ACS icon and enter in the “user password”

Recipe Format (for GH Full Control Only)

¾System Rate & Line Speed

¾Weigh Per Length Mode

¾Weight Per Area Mode

Hopper Setup

¾Hopper size

¾Reload Percentage

Extruder Setup

¾Maximum Extruder RPM

¾GHF Extruder Max. Throughput (GH-F Only)

Hauloff Setup (for GH Full

Control Only)

¾Hauloff enable/disable

¾Read/ Do Not read speed from COEX Master

¾Hauloff Max Speed

¾Calibrate Encoder

Calibration

¾Scale Calibration

¾Direct Scale Readout

¾Weight/RPM Calibration

Panel View Config

¾Panel view GH version

¾PLC GH version

Units

¾Lbs. vs Kgs.

Password

¾New Password

¾Verify Password

Alarm Log

¾View, print, and clear the alarm log

Alarm Setup

¾Min System Speed %

¾Max System Speed %

¾System Unstable Alarm Time

¾Maximum allowed reload time

¾Hopper % for low level alarm

¾Hopper % for no material alarm

¾Out of material alarm silence delay

Network Setup

¾IP Address

¾Subnet Mask

¾Send Config to ENI Module

¾Enable Ethernet Configurator

¾Enable or disable coexpert com

Chapter 3: Installation

30 of 60

Image 30

Sterling 882.00722.00 manual GH Controller Menu Structure, Recipe Page Start

Contents

GH-M Rate Monitor Allen-Bradley Controller Write Down Your Serial Numbers Here For Future Reference Event of Shipping Damage Shipping InfoUnpacking and Inspection If the Shipment is Not Complete Warranty Returns ReturnsCredit Returns Table of Contents Maintenance Safety How to Use This ManualSafety Symbols Used in this Manual Safety Tags and Warning Labels Description Follow all Safety Codes Wear Safety Glasses and Work Gloves Responsibility General ResponsibilityOperator Responsibility Remember Maintenance Responsibility Reporting a Safety Defect Models Covered in This Manual AccessoriesFunctional Description General Description Customer Service Typical Features and Components Mechanical FeaturesController Features Extruder Inductive Proximity Switch System Component DescriptionSurge Hopper Open Weigh Hopper Function Typical GH-M Operator Screen Operator Screens Common to all GH Systems Typical Setup Screens Optional Components Ethernet Module Safety Features Pneumatic Slide Gate below surge hopperLow Level Proximity Sensors Mounting Configurations InstallationMechanical Installation Uncrating the Equipment Electrical Connections Machine Mount Pneumatic Connections Mechanical Set-up Weigh Hopper InstallationInitial Set-up Extruder RPM connection Final Connections Display Startup Screen Controller Set-up GH Controller Menu Structure Recipe Page Start GH Calibration Weigh Hopper Load Cell Calibration Display Calibration Menu Screen Hopper Size Setup WTP/RPM Calibration Extruder Setup Hauloff Setup and Encoder Calibration Alarm Setup Network Setup Setting Date and Time PanelView Configuration Screen GH-M Operation Procedures OperationOperator Displays GH Full Control Operation Procedures Typical Operator Screen for GH Full Control system GH-F Gravimetric Feeder Operation Procedures Common Screens Typical Manual Control Operator Screen Alarm Flags Alarms with DescriptionsPrint Inventory Maintenance Preventative Maintenance Schedule Electrical Preventative MaintenanceCorrective Maintenance Internal Components of the Control Panel Input Signals to Programmable Controller Output Signals from Programmable Controller Troubleshooting Introduction Problem Corrective action Problem Warranty Restrictions Warranty and Spare PartsWarranty Specifications Warranty Liabilities Customer Responsibilities Annex B Information Typical Surge Hopper Assembly Parts List Addendum Service Supervisor Information PasswordsProgrammable Settings Typical Engineering Only Setup Screen Full Hopper Method Percent of hopper Method DefaultExtruder Pulse Count Method WTP/RPM Filter Max Allowed WTP/RPM Mechanical Options Screen Diagnostics Screen Typical Analog Options Analog options screen Alarm Log Customer Setup MenuPassword Protection Units Below are the items that can be accessed for the GH Hopper Allen-Bradley Communications Manual Appendix Reload TOO Long Fixed Decimal Explanation Service Department Sales Department Parts DepartmentContract Department