Manuals / Subaru Robin Power Products / Lawn and Garden / Portable Generator

Subaru Robin Power Products R1700i 5-3DISASSEMBLY PROCEDURES, 19, 5-3-2Remove the rear cover

Models: R1700i

1 52

Download 52 pages 54.96 Kb

Page 22

Image 22

5-3) DISASSEMBLY PROCEDURES

Please disassemble in the order of the procedure below.

5-3-1 Remove the side panels (Left, Right)

Remove the side panels.

M6 x 16.5mm Bolt : 2 pcs.

Tools : Screw driver

5-3-2 Remove the rear cover

Remove the rear cover by unscrewing the four screws.

M6 x 20mm Screw and Washer : 4pcs.

Tools : Screw driver

5-3-3 Remove rolling wire, choke wire

Loosen the screw that holds the choke wire.

And remove it from the swivel.

Unwind the rolling wire by hand or pliers, and pull up.

Tools : Screw driver, pliers

Side Panel

Rear cover

Choke wire

Rolling wire

– 19 –

Page 22

Image 22

Subaru Robin Power Products R1700i service manual 5-3DISASSEMBLY PROCEDURES, 19, 5-3-1Remove the side panels Left, Right

Contents

Model R1700i GENERATORPUB-GS1950Rev. 09/04 Page CONTENTS MODEL 1. SPECIFICATIONSR1700i 2. GENERAL DESCRIPTION 2-1EXTERNAL VIEW R1700i2-2CONTROL PANEL R1700i 1 ENGINE SWITCH3 OIL SENSOR LAMP 4AUTO POWER SAVE SWITCH2 PILOT LAMP and OVERLOAD LAMP PILOT LAMP6 DC TERMINALS 5 AC RECEPTACLES7DC CIRCUIT BREAKER R1700i 2-4GENERATOR ASSEMBLYSerial number and Production number Label 3. RANGE OF APPLICATIONS 3Mercury lamps with a smaller power factorPage Page 4. MEASURING AND CHECKING PROCEDURES 4-1INSTRUMENTS5MEAGER TESTER 4CIRCUIT TESTER For measuring resistance, etc6TACHOMETER MODEL Dr.RobinSpecification 4-2AC OUTPUT MEASURING4-3MEASURING INSULATION RESISTANCE ModelPage 4-4CHECKING FUNCTIONAL MEMBERS Page Below the lower level ON continuity Oil capacity 0.4 liters5-1PRECAUTIONS 5. ASSEMBLY AND DISASSEMBLY5-2SPECIAL TOOLS – 19 – 5-3DISASSEMBLY PROCEDURES5-3-3Remove rolling wire, choke wire 5-3-1Remove the side panels Left, Right5-3-6Remove the case body Left, Right 5-3-4Remove the recoil starter handle5-3-5Remove the control panel Upper part of the case body5-3-8Remove fuel cock bracket 5-3-7Remove rear frame5-3-9Remove the fuel tank 5-3-11Remove the inverter unit 5-3-10Remove the control panel5-3-12Remove the fuel pipes 5-3-14Remove the front frame 5-3-13Remove the air cleaner and carburetor5-3-15Remove the base inverter 5-3-16Remove the Stator / Rear cover 5-3-17Remove the rotor5-3-19Remove the flywheel 5-3-18Remove Blower housing5-3-20Remove recoil starter 5-3-22Remove the ignition coil 5-3-21Remove the muffler5-3-23Remove the cylinder baffle Tightening torque 5-4REASSEMBLY PROCEDURES5-4-1Cylinder baffle 70-905.2-6.6ft・lbs 5-4-5Flywheel 5-4-4Recoil starterTightening torque 7.0-9.0N・m 70-90kgf・cm Air gap 0.5 mmTightening torque 3.0-5.0N・m 30-50kgf・cm 5-4-8Blower housing5-4-7Pulsar coil and grommet 2.2-3.7ft・lbs5-4-9Rotor 5-4-10Rear cover, stator5-4-11Base Inverter 5-4-13Air cleaner bottom plate and carburetor5-4-14Air cleaner Tightening torque5-4-15Fuel pipe 5-4-17Installing coupler5-4-16Inverter unit 5-4-19Fuel cock bracket 5-4-18Fuel tank5-4-20Rear frame 5-4-21Case body, control panel 5-4-22Recoil starter and guideTightening torque 5-4-23Choke wire and rolling wire5-4-24Rear cover 30-405-5RECOIL STARTER 1 Disassembly proceduresPage 2 Assembly procedure – 38 –Page 3 Checking items after assembly 4 When 6.TROUBLESHOOTING No output power or Lower outputImproper revolutions Electronic throttle Engine does not start Start failure Spark Plug - BMR4A NGKWiring color cord 7. WIRING DIAGRAMR1700i 50Hz-230V Wiring color cord R1700i 50Hz-240VWiring color cord R1700i 60Hz-120VPage Copyright 2004 Robin America, Inc