Manuals / Subaru Robin Power Products / Lawn and Garden / Portable Generator

Subaru Robin Power Products R1700i 5-3-7Remove rear frame, 5-3-8Remove fuel cock bracket

Models: R1700i

1 52

Download 52 pages 54.96 Kb

Page 24

5-3-7 Remove rear frame

5-3-7 Remove rear frame

Remove the rear frame.

Front

frame

Rear frame

5-3-8 Remove fuel cock bracket

Remove the fuel cock bracket.

M6 x 12mm Flange bolt : 1pce.

M6 Nut : 1pce.

Tools : 10mm Box wrench

NOTE 1: Be sure to close the fuel cock before removing the fuel pipe.

(Engine switch in the off position)

NOTE 2: A little fuel comes out from the fuel pump when unplug the pipe.

5-3-9 Remove the fuel tank

Remove the fuel tank with the fuel cock still connected.

Fuel pump

Unplug the pipe

Fuel cock bracket

Fuel tank

– 21 –

Image 24

Subaru Robin Power Products R1700i 5-3-7Remove rear frame, 5-3-8Remove fuel cock bracket, 5-3-9Remove the fuel tank

Contents

R1700i GENERATOR ModelPUB-GS1950Rev. 09/04 Page CONTENTS 1. SPECIFICATIONS MODELR1700i 2. GENERAL DESCRIPTION 2-1EXTERNAL VIEW R1700i2-2CONTROL PANEL R1700i 1 ENGINE SWITCH4AUTO POWER SAVE SWITCH 2 PILOT LAMP and OVERLOAD LAMP3 OIL SENSOR LAMP PILOT LAMP5 AC RECEPTACLES 6 DC TERMINALS7DC CIRCUIT BREAKER 2-4GENERATOR ASSEMBLY R1700iSerial number and Production number Label 3. RANGE OF APPLICATIONS 3Mercury lamps with a smaller power factorPage Page 4. MEASURING AND CHECKING PROCEDURES 4-1INSTRUMENTS4CIRCUIT TESTER For measuring resistance, etc 5MEAGER TESTER6TACHOMETER MODEL Dr.Robin4-2AC OUTPUT MEASURING 4-3MEASURING INSULATION RESISTANCESpecification ModelPage 4-4CHECKING FUNCTIONAL MEMBERS Page Below the lower level ON continuity Oil capacity 0.4 liters5. ASSEMBLY AND DISASSEMBLY 5-1PRECAUTIONS5-2SPECIAL TOOLS 5-3DISASSEMBLY PROCEDURES 5-3-3Remove rolling wire, choke wire– 19 – 5-3-1Remove the side panels Left, Right5-3-4Remove the recoil starter handle 5-3-5Remove the control panel5-3-6Remove the case body Left, Right Upper part of the case body5-3-7Remove rear frame 5-3-8Remove fuel cock bracket5-3-9Remove the fuel tank 5-3-10Remove the control panel 5-3-11Remove the inverter unit5-3-12Remove the fuel pipes 5-3-13Remove the air cleaner and carburetor 5-3-14Remove the front frame5-3-15Remove the base inverter 5-3-16Remove the Stator / Rear cover 5-3-17Remove the rotor5-3-18Remove Blower housing 5-3-19Remove the flywheel5-3-20Remove recoil starter 5-3-21Remove the muffler 5-3-22Remove the ignition coil5-3-23Remove the cylinder baffle 5-4REASSEMBLY PROCEDURES 5-4-1Cylinder baffleTightening torque 70-905-4-4Recoil starter Tightening torque 7.0-9.0N・m 70-90kgf・cm5.2-6.6ft・lbs 5-4-5Flywheel Air gap 0.5 mm5-4-8Blower housing 5-4-7Pulsar coil and grommetTightening torque 3.0-5.0N・m 30-50kgf・cm 2.2-3.7ft・lbs5-4-9Rotor 5-4-10Rear cover, stator5-4-13Air cleaner bottom plate and carburetor 5-4-14Air cleaner5-4-11Base Inverter Tightening torque5-4-17Installing coupler 5-4-15Fuel pipe5-4-16Inverter unit 5-4-18Fuel tank 5-4-19Fuel cock bracket5-4-20Rear frame 5-4-21Case body, control panel 5-4-22Recoil starter and guide5-4-23Choke wire and rolling wire 5-4-24Rear coverTightening torque 30-405-5RECOIL STARTER 1 Disassembly proceduresPage 2 Assembly procedure – 38 –Page 3 Checking items after assembly 4 When 6.TROUBLESHOOTING No output power or Lower outputImproper revolutions Electronic throttle Engine does not start Start failure Spark Plug - BMR4A NGK7. WIRING DIAGRAM Wiring color cordR1700i 50Hz-230V Wiring color cord R1700i 50Hz-240VWiring color cord R1700i 60Hz-120VPage Copyright 2004 Robin America, Inc