Manuals / Subaru Robin Power Products / Lawn and Garden / Portable Generator

Subaru Robin Power Products R1700i service manual

Models: R1700i

1 52

Download 52 pages 54.96 Kb

Page 42

– 39 –

(4) Inserting the rope. (this should be done by two people)

-1 Thread the rope through the reel where the rope hole on the reel and rope guide are aligned.

-2 Thread the rope end through the rope guide and the rope hole of the reel, and pull 20cm out from the reel.

-3 Tight the end of the rope.

(5) Keep pressure on the spring

-1 Feed the rope .(the length of one rotation of the reel) from the attached hole of the reel and pull it out from teh hole of the case.

On the reel side, let the rope that was pulled out hang over the notch of the reel.

About 20cm

Fixed hole

Rope

Cut of the reel

Pull off hole

– 39 –

Image 42

Subaru Robin Power Products R1700i service manual

Contents

R1700i GENERATOR ModelPUB-GS1950Rev. 09/04 Page CONTENTS 1. SPECIFICATIONS MODELR1700i 2. GENERAL DESCRIPTION 2-1EXTERNAL VIEW R1700i2-2CONTROL PANEL R1700i 1 ENGINE SWITCH3 OIL SENSOR LAMP 4AUTO POWER SAVE SWITCH2 PILOT LAMP and OVERLOAD LAMP PILOT LAMP5 AC RECEPTACLES 6 DC TERMINALS7DC CIRCUIT BREAKER 2-4GENERATOR ASSEMBLY R1700iSerial number and Production number Label 3. RANGE OF APPLICATIONS 3Mercury lamps with a smaller power factorPage Page 4. MEASURING AND CHECKING PROCEDURES 4-1INSTRUMENTS4CIRCUIT TESTER For measuring resistance, etc 5MEAGER TESTER6TACHOMETER MODEL Dr.RobinSpecification 4-2AC OUTPUT MEASURING4-3MEASURING INSULATION RESISTANCE ModelPage 4-4CHECKING FUNCTIONAL MEMBERS Page Below the lower level ON continuity Oil capacity 0.4 liters5. ASSEMBLY AND DISASSEMBLY 5-1PRECAUTIONS5-2SPECIAL TOOLS – 19 – 5-3DISASSEMBLY PROCEDURES5-3-3Remove rolling wire, choke wire 5-3-1Remove the side panels Left, Right5-3-6Remove the case body Left, Right 5-3-4Remove the recoil starter handle5-3-5Remove the control panel Upper part of the case body5-3-7Remove rear frame 5-3-8Remove fuel cock bracket5-3-9Remove the fuel tank 5-3-10Remove the control panel 5-3-11Remove the inverter unit5-3-12Remove the fuel pipes 5-3-13Remove the air cleaner and carburetor 5-3-14Remove the front frame5-3-15Remove the base inverter 5-3-16Remove the Stator / Rear cover 5-3-17Remove the rotor5-3-18Remove Blower housing 5-3-19Remove the flywheel5-3-20Remove recoil starter 5-3-21Remove the muffler 5-3-22Remove the ignition coil5-3-23Remove the cylinder baffle Tightening torque 5-4REASSEMBLY PROCEDURES5-4-1Cylinder baffle 70-905.2-6.6ft・lbs 5-4-5Flywheel 5-4-4Recoil starterTightening torque 7.0-9.0N・m 70-90kgf・cm Air gap 0.5 mmTightening torque 3.0-5.0N・m 30-50kgf・cm 5-4-8Blower housing5-4-7Pulsar coil and grommet 2.2-3.7ft・lbs5-4-9Rotor 5-4-10Rear cover, stator5-4-11Base Inverter 5-4-13Air cleaner bottom plate and carburetor5-4-14Air cleaner Tightening torque5-4-17Installing coupler 5-4-15Fuel pipe5-4-16Inverter unit 5-4-18Fuel tank 5-4-19Fuel cock bracket5-4-20Rear frame 5-4-21Case body, control panel 5-4-22Recoil starter and guideTightening torque 5-4-23Choke wire and rolling wire5-4-24Rear cover 30-405-5RECOIL STARTER 1 Disassembly proceduresPage 2 Assembly procedure – 38 –Page 3 Checking items after assembly 4 When 6.TROUBLESHOOTING No output power or Lower outputImproper revolutions Electronic throttle Engine does not start Start failure Spark Plug - BMR4A NGK7. WIRING DIAGRAM Wiring color cordR1700i 50Hz-230V Wiring color cord R1700i 50Hz-240VWiring color cord R1700i 60Hz-120VPage Copyright 2004 Robin America, Inc