Manuals / Subaru Robin Power Products / Lawn and Garden / Portable Generator

Subaru Robin Power Products R1700i 5-4-4Recoil starter, Tightening torque 7.0-9.0N・m 70-90kgf・cm

Models: R1700i

1 52

Download 52 pages 54.96 Kb

Page 31

Image 31

5-4-4 Recoil starter

Attach the recoil starter to the crankcase.

M6 x 18mm Flange bolt : 3pcs.

Tightening torque : 7.0-9.0 N・m

70-90 kgf・cm

(5.2-6.6 ft・lbs)

5-4-5 Flywheel

Install the flywheel.

M8 x 25 Bolt and washer : 1pce.

8.5D x 28D x 3.2T Washer : 1pce.

Tightening torque : 19.0-21.0 N・m 190-210 kgf・cm (14.0-15.5 ft・lbs)

NOTE : Wipe off any oil from the tapered shaft and hole

before assembling.

5-4-6 Air gap adjustment of flywheel and pulsar coil

Adjust the air gap between flywheel and pulsar coil to 0.5mm with a feeler gauge. Attach the pulsar coil to the engine.

Air gap : 0.5 mm

Recoil starter

Flywheel

Pulsar coil

Flywheel

– 28 –

Page 31

Image 31

Subaru Robin Power Products R1700i 5-4-4Recoil starter, Tightening torque 7.0-9.0N・m 70-90kgf・cm, Air gap 0.5 mm

Contents

Model R1700i GENERATORPUB-GS1950Rev. 09/04 Page CONTENTS MODEL 1. SPECIFICATIONSR1700i 2-1EXTERNAL VIEW R1700i 2. GENERAL DESCRIPTION1 ENGINE SWITCH 2-2CONTROL PANEL R1700iPILOT LAMP 4AUTO POWER SAVE SWITCH2 PILOT LAMP and OVERLOAD LAMP 3 OIL SENSOR LAMP6 DC TERMINALS 5 AC RECEPTACLES7DC CIRCUIT BREAKER R1700i 2-4GENERATOR ASSEMBLYSerial number and Production number Label 3Mercury lamps with a smaller power factor 3. RANGE OF APPLICATIONSPage Page 4-1INSTRUMENTS 4. MEASURING AND CHECKING PROCEDURES5MEAGER TESTER 4CIRCUIT TESTER For measuring resistance, etc6TACHOMETER Dr.Robin MODELModel 4-2AC OUTPUT MEASURING4-3MEASURING INSULATION RESISTANCE SpecificationPage 4-4CHECKING FUNCTIONAL MEMBERS Page Oil capacity 0.4 liters Below the lower level ON continuity5-1PRECAUTIONS 5. ASSEMBLY AND DISASSEMBLY5-2SPECIAL TOOLS 5-3-1Remove the side panels Left, Right 5-3DISASSEMBLY PROCEDURES5-3-3Remove rolling wire, choke wire – 19 –Upper part of the case body 5-3-4Remove the recoil starter handle5-3-5Remove the control panel 5-3-6Remove the case body Left, Right5-3-8Remove fuel cock bracket 5-3-7Remove rear frame5-3-9Remove the fuel tank 5-3-11Remove the inverter unit 5-3-10Remove the control panel5-3-12Remove the fuel pipes 5-3-14Remove the front frame 5-3-13Remove the air cleaner and carburetor5-3-15Remove the base inverter 5-3-17Remove the rotor 5-3-16Remove the Stator / Rear cover5-3-19Remove the flywheel 5-3-18Remove Blower housing5-3-20Remove recoil starter 5-3-22Remove the ignition coil 5-3-21Remove the muffler5-3-23Remove the cylinder baffle 70-90 5-4REASSEMBLY PROCEDURES5-4-1Cylinder baffle Tightening torqueAir gap 0.5 mm 5-4-4Recoil starterTightening torque 7.0-9.0N・m 70-90kgf・cm 5.2-6.6ft・lbs 5-4-5Flywheel2.2-3.7ft・lbs 5-4-8Blower housing5-4-7Pulsar coil and grommet Tightening torque 3.0-5.0N・m 30-50kgf・cm5-4-10Rear cover, stator 5-4-9RotorTightening torque 5-4-13Air cleaner bottom plate and carburetor5-4-14Air cleaner 5-4-11Base Inverter5-4-15Fuel pipe 5-4-17Installing coupler5-4-16Inverter unit 5-4-19Fuel cock bracket 5-4-18Fuel tank5-4-20Rear frame 5-4-22Recoil starter and guide 5-4-21Case body, control panel30-40 5-4-23Choke wire and rolling wire5-4-24Rear cover Tightening torque1 Disassembly procedures 5-5RECOIL STARTERPage – 38 – 2 Assembly procedurePage 3 Checking items after assembly 4 When No output power or Lower output 6.TROUBLESHOOTINGImproper revolutions Electronic throttle Spark Plug - BMR4A NGK Engine does not start Start failureWiring color cord 7. WIRING DIAGRAMR1700i 50Hz-230V R1700i 50Hz-240V Wiring color cordR1700i 60Hz-120V Wiring color cordPage Copyright 2004 Robin America, Inc