Manuals / Subaru Robin Power Products / Lawn and Garden / Portable Generator

Subaru Robin Power Products R1700i service manual 5-4-7Pulsar coil and grommet, 2.2-3.7ft・lbs

Models: R1700i

1 52

Download 52 pages 54.96 Kb

Page 32

5-4-7 Pulsar coil and grommet

5-4-7 Pulsar coil and grommet

Tighten the bolt in place, making adjustments according

to 5-4-6.

M6 x 8mm Flange bolt : 2pcs.

Tightening torque : 3.0-5.0 N・m

30-50 kgf・cm

(2.2-3.7 ft・lbs)

Place the pulsar coil wires along the groove of the grommet and recoil guide to make it easier to assemble the blower housing.

Caution : Do not forget to put the 2 pieces of pipe knock.

Recoil guide	Pulsar coil
Flywheel	Grommet
Flywheel
	Pulsar coil harness

5-4-8 Blower housing

Install the blower housing

M8 x 55mm Flange bolt : 1pce.

M8 x 90mm Flange bolt : 3pcs.

Tightening torque : 18.0-20.0 N・m 180-200 kgf・cm (13.3-14.8 ft・lbs)

NOTE: Insert the grommet (pulsar coil harness) and recoil guide into the blower housing securely.

Blower housing

– 29 –

Image 32

Subaru Robin Power Products R1700i 5-4-7Pulsar coil and grommet, Tightening torque 3.0-5.0N・m 30-50kgf・cm, 2.2-3.7ft・lbs

Contents

PUB-GS1950Rev. 09/04 R1700i GENERATORModel Page CONTENTS R1700i 1. SPECIFICATIONSMODEL 2. GENERAL DESCRIPTION 2-1EXTERNAL VIEW R1700i2-2CONTROL PANEL R1700i 1 ENGINE SWITCH4AUTO POWER SAVE SWITCH 2 PILOT LAMP and OVERLOAD LAMP3 OIL SENSOR LAMP PILOT LAMP7DC CIRCUIT BREAKER 5 AC RECEPTACLES6 DC TERMINALS Serial number and Production number Label 2-4GENERATOR ASSEMBLYR1700i 3. RANGE OF APPLICATIONS 3Mercury lamps with a smaller power factorPage Page 4. MEASURING AND CHECKING PROCEDURES 4-1INSTRUMENTS6TACHOMETER 4CIRCUIT TESTER For measuring resistance, etc5MEAGER TESTER MODEL Dr.Robin4-2AC OUTPUT MEASURING 4-3MEASURING INSULATION RESISTANCESpecification ModelPage 4-4CHECKING FUNCTIONAL MEMBERS Page Below the lower level ON continuity Oil capacity 0.4 liters5-2SPECIAL TOOLS 5. ASSEMBLY AND DISASSEMBLY5-1PRECAUTIONS 5-3DISASSEMBLY PROCEDURES 5-3-3Remove rolling wire, choke wire– 19 – 5-3-1Remove the side panels Left, Right5-3-4Remove the recoil starter handle 5-3-5Remove the control panel5-3-6Remove the case body Left, Right Upper part of the case body5-3-9Remove the fuel tank 5-3-7Remove rear frame5-3-8Remove fuel cock bracket 5-3-12Remove the fuel pipes 5-3-10Remove the control panel5-3-11Remove the inverter unit 5-3-15Remove the base inverter 5-3-13Remove the air cleaner and carburetor5-3-14Remove the front frame 5-3-16Remove the Stator / Rear cover 5-3-17Remove the rotor5-3-20Remove recoil starter 5-3-18Remove Blower housing5-3-19Remove the flywheel 5-3-23Remove the cylinder baffle 5-3-21Remove the muffler5-3-22Remove the ignition coil 5-4REASSEMBLY PROCEDURES 5-4-1Cylinder baffleTightening torque 70-905-4-4Recoil starter Tightening torque 7.0-9.0N・m 70-90kgf・cm5.2-6.6ft・lbs 5-4-5Flywheel Air gap 0.5 mm5-4-8Blower housing 5-4-7Pulsar coil and grommetTightening torque 3.0-5.0N・m 30-50kgf・cm 2.2-3.7ft・lbs5-4-9Rotor 5-4-10Rear cover, stator5-4-13Air cleaner bottom plate and carburetor 5-4-14Air cleaner5-4-11Base Inverter Tightening torque5-4-16Inverter unit 5-4-17Installing coupler5-4-15Fuel pipe 5-4-20Rear frame 5-4-18Fuel tank5-4-19Fuel cock bracket 5-4-21Case body, control panel 5-4-22Recoil starter and guide5-4-23Choke wire and rolling wire 5-4-24Rear coverTightening torque 30-405-5RECOIL STARTER 1 Disassembly proceduresPage 2 Assembly procedure – 38 –Page 3 Checking items after assembly 4 When 6.TROUBLESHOOTING No output power or Lower outputImproper revolutions Electronic throttle Engine does not start Start failure Spark Plug - BMR4A NGKR1700i 50Hz-230V 7. WIRING DIAGRAMWiring color cord Wiring color cord R1700i 50Hz-240VWiring color cord R1700i 60Hz-120VPage Copyright 2004 Robin America, Inc