Manuals / Subaru Robin Power Products / Lawn and Garden / Portable Generator

Subaru Robin Power Products R1700i 5-3-16Remove the Stator / Rear cover, 5-3-17Remove the rotor

Models: R1700i

1 52

Download 52 pages 54.96 Kb

Page 27

Image 27

5-3-16 Remove the Stator / Rear cover

Remove the Stator / Rear cover.

M6 x 25mm Flange bolt : 3pcs.

Tools : 10mm Box wrench

NOTE 1: The stator is attached to the rear cover, both can be removed together.

They are attached with a strong magnetic force, so pull out straight.

The stator and the rotor are pulling each other by a strong magnetic force. Please use caution when removing the stator in order to prevent from getting injury on fingers.

5-3-17 Remove the rotor

Remove the rotor.

M6 x 20mm Flange bolt : 3pcs.

Tools : 10mm Box wrench

NOTE : There is a strong magnetic field around the rotor. Use atmost care to avoid foreign substances such as small iron particles stick to the rotor.

Rear cover

Stator

Rotor

– 24 –

Page 27

Image 27

Subaru Robin Power Products R1700i service manual 5-3-16Remove the Stator / Rear cover, 5-3-17Remove the rotor

Contents

R1700i GENERATOR ModelPUB-GS1950Rev. 09/04 Page CONTENTS 1. SPECIFICATIONS MODELR1700i 2-1EXTERNAL VIEW R1700i 2. GENERAL DESCRIPTION1 ENGINE SWITCH 2-2CONTROL PANEL R1700iPILOT LAMP 4AUTO POWER SAVE SWITCH2 PILOT LAMP and OVERLOAD LAMP 3 OIL SENSOR LAMP5 AC RECEPTACLES 6 DC TERMINALS7DC CIRCUIT BREAKER 2-4GENERATOR ASSEMBLY R1700iSerial number and Production number Label 3Mercury lamps with a smaller power factor 3. RANGE OF APPLICATIONSPage Page 4-1INSTRUMENTS 4. MEASURING AND CHECKING PROCEDURES4CIRCUIT TESTER For measuring resistance, etc 5MEAGER TESTER6TACHOMETER Dr.Robin MODELModel 4-2AC OUTPUT MEASURING4-3MEASURING INSULATION RESISTANCE SpecificationPage 4-4CHECKING FUNCTIONAL MEMBERS Page Oil capacity 0.4 liters Below the lower level ON continuity5. ASSEMBLY AND DISASSEMBLY 5-1PRECAUTIONS5-2SPECIAL TOOLS 5-3-1Remove the side panels Left, Right 5-3DISASSEMBLY PROCEDURES5-3-3Remove rolling wire, choke wire – 19 –Upper part of the case body 5-3-4Remove the recoil starter handle5-3-5Remove the control panel 5-3-6Remove the case body Left, Right5-3-7Remove rear frame 5-3-8Remove fuel cock bracket5-3-9Remove the fuel tank 5-3-10Remove the control panel 5-3-11Remove the inverter unit5-3-12Remove the fuel pipes 5-3-13Remove the air cleaner and carburetor 5-3-14Remove the front frame5-3-15Remove the base inverter 5-3-17Remove the rotor 5-3-16Remove the Stator / Rear cover5-3-18Remove Blower housing 5-3-19Remove the flywheel5-3-20Remove recoil starter 5-3-21Remove the muffler 5-3-22Remove the ignition coil5-3-23Remove the cylinder baffle 70-90 5-4REASSEMBLY PROCEDURES5-4-1Cylinder baffle Tightening torqueAir gap 0.5 mm 5-4-4Recoil starterTightening torque 7.0-9.0N・m 70-90kgf・cm 5.2-6.6ft・lbs 5-4-5Flywheel2.2-3.7ft・lbs 5-4-8Blower housing5-4-7Pulsar coil and grommet Tightening torque 3.0-5.0N・m 30-50kgf・cm5-4-10Rear cover, stator 5-4-9RotorTightening torque 5-4-13Air cleaner bottom plate and carburetor5-4-14Air cleaner 5-4-11Base Inverter5-4-17Installing coupler 5-4-15Fuel pipe5-4-16Inverter unit 5-4-18Fuel tank 5-4-19Fuel cock bracket5-4-20Rear frame 5-4-22Recoil starter and guide 5-4-21Case body, control panel30-40 5-4-23Choke wire and rolling wire5-4-24Rear cover Tightening torque1 Disassembly procedures 5-5RECOIL STARTERPage – 38 – 2 Assembly procedurePage 3 Checking items after assembly 4 When No output power or Lower output 6.TROUBLESHOOTINGImproper revolutions Electronic throttle Spark Plug - BMR4A NGK Engine does not start Start failure7. WIRING DIAGRAM Wiring color cordR1700i 50Hz-230V R1700i 50Hz-240V Wiring color cordR1700i 60Hz-120V Wiring color cordPage Copyright 2004 Robin America, Inc