Manuals / Subaru Robin Power Products / Lawn and Garden / Portable Generator

Subaru Robin Power Products R1700i 5-3-18Remove Blower housing, 5-3-19Remove the flywheel

Models: R1700i

1 52

Download 52 pages 54.96 Kb

Page 28

Image 28

5-3-18 Remove Blower housing

Remove the blower housing.

M8 x 55mm Flange bolt : 1pce.

M8 x 90mm Flange bolt : 3pcs.

Tools : 12mm Box wrench

NOTE : The pipe knock is attached to two places.

Blower Housing

5-3-19 Remove the flywheel

Remove the flywheel.

M8 x 20 Bolt and washer : 1pce.

NOTE: Use a Flywheel puller (Available on market) for the taper.

Tools : 12mm Box wrench

Flywheel puller (Available on market)

Flywheel

5-3-20 Remove recoil starter

Remove the recoil starter.

M6 x 20mm AY Bolt : 3pcs.

Tools : 10mm Box wrench

NOTE: For the maintenance of recoil starter, please refer to item "5-5) Disassembly and assembly of the recoil starter".

Recoil starter

– 25 –

Page 28

Image 28

Subaru Robin Power Products R1700i 5-3-18Remove Blower housing, 5-3-19Remove the flywheel, 5-3-20Remove recoil starter

Contents

Model R1700i GENERATORPUB-GS1950Rev. 09/04 Page CONTENTS MODEL 1. SPECIFICATIONSR1700i 2. GENERAL DESCRIPTION 2-1EXTERNAL VIEW R1700i2-2CONTROL PANEL R1700i 1 ENGINE SWITCH4AUTO POWER SAVE SWITCH 2 PILOT LAMP and OVERLOAD LAMP3 OIL SENSOR LAMP PILOT LAMP6 DC TERMINALS 5 AC RECEPTACLES7DC CIRCUIT BREAKER R1700i 2-4GENERATOR ASSEMBLYSerial number and Production number Label 3. RANGE OF APPLICATIONS 3Mercury lamps with a smaller power factorPage Page 4. MEASURING AND CHECKING PROCEDURES 4-1INSTRUMENTS5MEAGER TESTER 4CIRCUIT TESTER For measuring resistance, etc6TACHOMETER MODEL Dr.Robin4-2AC OUTPUT MEASURING 4-3MEASURING INSULATION RESISTANCESpecification ModelPage 4-4CHECKING FUNCTIONAL MEMBERS Page Below the lower level ON continuity Oil capacity 0.4 liters5-1PRECAUTIONS 5. ASSEMBLY AND DISASSEMBLY5-2SPECIAL TOOLS 5-3DISASSEMBLY PROCEDURES 5-3-3Remove rolling wire, choke wire– 19 – 5-3-1Remove the side panels Left, Right5-3-4Remove the recoil starter handle 5-3-5Remove the control panel5-3-6Remove the case body Left, Right Upper part of the case body5-3-8Remove fuel cock bracket 5-3-7Remove rear frame5-3-9Remove the fuel tank 5-3-11Remove the inverter unit 5-3-10Remove the control panel5-3-12Remove the fuel pipes 5-3-14Remove the front frame 5-3-13Remove the air cleaner and carburetor5-3-15Remove the base inverter 5-3-16Remove the Stator / Rear cover 5-3-17Remove the rotor5-3-19Remove the flywheel 5-3-18Remove Blower housing5-3-20Remove recoil starter 5-3-22Remove the ignition coil 5-3-21Remove the muffler5-3-23Remove the cylinder baffle 5-4REASSEMBLY PROCEDURES 5-4-1Cylinder baffleTightening torque 70-905-4-4Recoil starter Tightening torque 7.0-9.0N・m 70-90kgf・cm5.2-6.6ft・lbs 5-4-5Flywheel Air gap 0.5 mm5-4-8Blower housing 5-4-7Pulsar coil and grommetTightening torque 3.0-5.0N・m 30-50kgf・cm 2.2-3.7ft・lbs5-4-9Rotor 5-4-10Rear cover, stator5-4-13Air cleaner bottom plate and carburetor 5-4-14Air cleaner5-4-11Base Inverter Tightening torque5-4-15Fuel pipe 5-4-17Installing coupler5-4-16Inverter unit 5-4-19Fuel cock bracket 5-4-18Fuel tank5-4-20Rear frame 5-4-21Case body, control panel 5-4-22Recoil starter and guide5-4-23Choke wire and rolling wire 5-4-24Rear coverTightening torque 30-405-5RECOIL STARTER 1 Disassembly proceduresPage 2 Assembly procedure – 38 –Page 3 Checking items after assembly 4 When 6.TROUBLESHOOTING No output power or Lower outputImproper revolutions Electronic throttle Engine does not start Start failure Spark Plug - BMR4A NGKWiring color cord 7. WIRING DIAGRAMR1700i 50Hz-230V Wiring color cord R1700i 50Hz-240VWiring color cord R1700i 60Hz-120VPage Copyright 2004 Robin America, Inc