Manuals / Subaru Robin Power Products / Lawn and Garden / Portable Generator

Subaru Robin Power Products R1700i 5-4REASSEMBLY PROCEDURES, 5-4-1Cylinder baffle, 70-90, kgf・cm

Models: R1700i

1 52

Download 52 pages 54.96 Kb

Page 30

5-4) REASSEMBLY PROCEDURES

5-4) REASSEMBLY PROCEDURES

5-4-1 Cylinder baffle

Install the cylinder baffle. (Tighten together) M8 x 16mm Flange bolt : 3pcs.

Tightening torque : 11.0-13.0 N・m 110-130 kgf・cm (8.1-9.6 ft・lbs)

M6 x 12mm Flange bolt : 1pce.

Tightening torque : 7.0-9.0	N・m
70-90	kgf・cm
(5.2-6.6	ft・lbs)

5-4-2 Ignition coil

Install the ignition coil into the ignition coil bracket and attach it to the engine.

Ignition coil tightening torque

Tightening torque : 3.0-5.0	N・m
30-50	kgf・cm
(2.2-3.7	ft・lbs)

Ignition coil bracket tightening torque

M6 x 14mm Flange bolt : 1pce.

	Tightening torque : 7.0-9.0	N・m
	70-90	kgf・cm
	(5.2-6.6	ft・lbs)

M8 Flange nut : 1pce.

	Tightening torque : 11.0-13.0	N・m
	110-130	kgf・cm
	(8.1-9.6	ft・lbs)

5-4-3 Muffler
Install the muffler.
	M8 x 80mm Flange bolt : 1pce.

	Tightening torque : 11.0-13.0	N・m
	110-130	kgf・cm
	(8.1-9.6	ft・lbs)

	M6 Flange nut : 2pcs.

	Tightening torque : 7.0-9.0	N・m
	70-90	kgf・cm
	(5.2-6.6	ft・lbs)

Cylinder baffle

Ignition coil

Muffler

– 27 –

Image 30

Subaru Robin Power Products R1700i 5-4REASSEMBLY PROCEDURES, 5-4-1Cylinder baffle, Tightening torque, 70-90, kgf・cm, 30-50

Contents

R1700i GENERATOR ModelPUB-GS1950Rev. 09/04 Page CONTENTS 1. SPECIFICATIONS MODELR1700i 2. GENERAL DESCRIPTION 2-1EXTERNAL VIEW R1700i2-2CONTROL PANEL R1700i 1 ENGINE SWITCH3 OIL SENSOR LAMP 4AUTO POWER SAVE SWITCH2 PILOT LAMP and OVERLOAD LAMP PILOT LAMP5 AC RECEPTACLES 6 DC TERMINALS7DC CIRCUIT BREAKER 2-4GENERATOR ASSEMBLY R1700iSerial number and Production number Label 3. RANGE OF APPLICATIONS 3Mercury lamps with a smaller power factorPage Page 4. MEASURING AND CHECKING PROCEDURES 4-1INSTRUMENTS4CIRCUIT TESTER For measuring resistance, etc 5MEAGER TESTER6TACHOMETER MODEL Dr.RobinSpecification 4-2AC OUTPUT MEASURING4-3MEASURING INSULATION RESISTANCE ModelPage 4-4CHECKING FUNCTIONAL MEMBERS Page Below the lower level ON continuity Oil capacity 0.4 liters5. ASSEMBLY AND DISASSEMBLY 5-1PRECAUTIONS5-2SPECIAL TOOLS – 19 – 5-3DISASSEMBLY PROCEDURES5-3-3Remove rolling wire, choke wire 5-3-1Remove the side panels Left, Right5-3-6Remove the case body Left, Right 5-3-4Remove the recoil starter handle5-3-5Remove the control panel Upper part of the case body5-3-7Remove rear frame 5-3-8Remove fuel cock bracket5-3-9Remove the fuel tank 5-3-10Remove the control panel 5-3-11Remove the inverter unit5-3-12Remove the fuel pipes 5-3-13Remove the air cleaner and carburetor 5-3-14Remove the front frame5-3-15Remove the base inverter 5-3-16Remove the Stator / Rear cover 5-3-17Remove the rotor5-3-18Remove Blower housing 5-3-19Remove the flywheel5-3-20Remove recoil starter 5-3-21Remove the muffler 5-3-22Remove the ignition coil5-3-23Remove the cylinder baffle Tightening torque 5-4REASSEMBLY PROCEDURES5-4-1Cylinder baffle 70-905.2-6.6ft・lbs 5-4-5Flywheel 5-4-4Recoil starterTightening torque 7.0-9.0N・m 70-90kgf・cm Air gap 0.5 mmTightening torque 3.0-5.0N・m 30-50kgf・cm 5-4-8Blower housing5-4-7Pulsar coil and grommet 2.2-3.7ft・lbs5-4-9Rotor 5-4-10Rear cover, stator5-4-11Base Inverter 5-4-13Air cleaner bottom plate and carburetor5-4-14Air cleaner Tightening torque5-4-17Installing coupler 5-4-15Fuel pipe5-4-16Inverter unit 5-4-18Fuel tank 5-4-19Fuel cock bracket5-4-20Rear frame 5-4-21Case body, control panel 5-4-22Recoil starter and guideTightening torque 5-4-23Choke wire and rolling wire5-4-24Rear cover 30-405-5RECOIL STARTER 1 Disassembly proceduresPage 2 Assembly procedure – 38 –Page 3 Checking items after assembly 4 When 6.TROUBLESHOOTING No output power or Lower outputImproper revolutions Electronic throttle Engine does not start Start failure Spark Plug - BMR4A NGK7. WIRING DIAGRAM Wiring color cordR1700i 50Hz-230V Wiring color cord R1700i 50Hz-240VWiring color cord R1700i 60Hz-120VPage Copyright 2004 Robin America, Inc