Manuals / Sun Microsystems / Computer Equipment / Power Supply

Sun Microsystems 2000E installation manual Related Documents, Application, Title, Part Number

Models: 2000E

1 54

Download 54 pages 35.54 Kb

Page 10

Related Documents

The following documents contain information that may be helpful after the upgrade is installed.

	Table P-1		Related Documents

Application	Title			Part Number

Safety	SPARCcenter 2000 Regulatory Compliance Manual			801-3051
Installation	SPARCcenter 2000 Installation Manual			800-6975
Diagnostics	SPARCcenter 2000 Post User’s Guide			800-7481
	OpenBoot Command Reference			800-6076
User’s Guides	SPARCcenter 2000 Storage Device User’s Guide			800-7009
	150MB Tape Drive User’s Guide			800-7020
	5.0 GB 8mm Tape Drive User’s Guide			800-7022
	10	Gbyte 8mm Tape Drive User’s Guide		801-7652
	14	Gbyte 8mm Tape Drive User’s Guide		802-1850
	20	Gbyte 4 mm Internal Tape Auto-Loader User’s Guide		801-4977
Service	SPARCcenter 2000 ServiceManual			801-2007

x	SPARCserver 2000E Power Supply Installation Manual—April 1995

Image 10

Sun Microsystems 2000E installation manual Related Documents, Application, Title, Part Number

Contents

Mountain View, CA 94043 U.S.A 415 960-1300 FAX 415 SPARCcenter 2000E Power Supply Installation ManualA Sun Microsystems, Inc. Business 2550 Garcia Avenue Part No. 802-2700-10 Revision -A, April1995 Sun Microsystems, Inc 2. Power Supply Installation Contents1. Before You Start SPARCserver 2000E Power Supply Installation Manual-April Figures Connecting the Power Cords LED Status Indicators TablesSafety Precautions 2-25SPARCserver 2000E Power Supply Installation Manual-April Preface How This Book Is OrganizedApplication Related DocumentsSPARCserver 2000E Power Supply Installation Manual-April TitleSymbol Shell Prompts in Command ExamplesWhat Typographic Changes Mean Typeface orNotes, Cautions, and Warnings 1.1 Safety Precautions Before You StartProblem 1.2 SymbolsThe following symbols mean PrecautionPROTECTIVE EARTH FUSE REPLACEMENTSTAND-BY CHASSIS1.3 Tools Required Power Supply Installation Perform these tasks in order to install a system power supply2.1 Operating System 2.2 Open Boot PROM2.3 Powering Down the System 3. Halt the system using the appropriate commandsOff Main Power OnDiagnostics Secure StandbyPower Supply Installation 2.5 Installing the Bottom Power Supply 2.4 Access2.5.1 Identifying a Redundant-Capable Cabinet Power Supply Installation 2.5.2 Installing the Supply2.5.2.1 Preparation ScrewsFigure 2-4 Disconnecting the Top Power Supply Power Cord 3. Remove the power supply cage cover panelPower cord SPARCserver 2000E Power Supply Installation Manual-AprilPower Supply Installation Remove the AC Distribution UnitPower supply cable #6 Phillips screws Phillips screws Cage cover panel Springfingers 2 each Remove screws, 6 placesRemove the Breaker Box 2.5.2.2 Power Supply Physical Installation Filter CableFigure 2-9 Installing the Bottom Power Supply Power supply cageInstall using 3 screws eachScrews 6 places Figure 2-10 Installing the Power Supply Mounting ScrewsPower Supply Installation 2-112.5.2.3 Main Bus Bar Installation 2.5.2.4 Power Harness Installation SPARCserver 2000E Power Supply Installation Manual-April A +12V C +12V Return E G -12V Return Power harness Part No B +12VCover panel Power harness Part No Power harness retainers D +12V Return F H -12V Return2.5.2.5 Cabling Filter Cable, Breaker Box and AC Distribution Unitd. Place the breaker box against power supply cage b. Replace the three Phillips screws and two #6-32 Phillips screws 2.5.2.6 Power Supply Sense Cable Plug it into J1 near the top of the supplyPower Supply Installation 2.5.2.7 Restore the SystemFigure 2-19 Replacing the Power Supply Compartment EMI Panel Screws3. Turn on the power switch on the AC distribution unit. See Figure 2.6 Restarting the System2. Turn the Local/Remote switch down, to Local. See Figure 4. Turn on power to the terminalRemote Local Figure 2-20 Local/Remote Switch LocationPower Supply Installation 2-216. Watch the terminal screen for any POST error messages Power supply maintenance should be scheduled2.7 Reading Boot Messages Figure 2-21 System Reset SwitchTable 2-1 summarizes LED status conditions during and after POST Power Supply Installation Power SupplyPower Supply BottomSPARCserver 2000E Power Supply Installation Manual-April A.1 Removal Procedures AccessA.1.1 Opening the Hinged Door A.1.2 Removing the Vented Front Panels SPARCserver 2000E Power Supply Installation Manual-April1. Loosen two slot-head captive screws near the panel base A.1.3 Removing the Side PanelsAccess 2. Tilt the panel bottom outA.1.4 Removing the EMI Shield The EMI shield is located behind the front panelsEMI shield #10 Phillips screws A.1.5 Rear Screen PanelAccess Figure 1-4 Removing the EMI ShieldA.2.1 EMI Panel A.2 Closing the SystemA.2.2 Rear Screen Panel A.2.3 Vented Front Panel A.2.4 Side PanelsSPARCserver 2000E Power Supply Installation Manual-April Dash Revision HistoryRevision DateSPARCserver 2000E Power Supply Installation Manual-April Reader Comments POSTAGE WILL BE PAID BY ADDRESSEE SUN MICROSYSTEMS, INC BUSINESS REPLY MAILNO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES Attn Manager, Hardware Publications MS MPK 2550 Garcia Avenue