Connecting the Control Panel | SUPER MICRO Computer 6014P-T manual

SUPERSERVER 6014P-T/6014P-TR User's Manual

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-3 for the pin locations of the various front control panel buttons and LED indi- cators. Please note that even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single ribbon cable to simplify their connec- tion. Make sure the red wire plugs into pin 1 as marked on the board. The other end connects to the Control Panel printed circuit board, located just behind the system status LEDs in the chassis.

See the Connector Deﬁ nitions section in this chapter for details and pin descrip- tions of JF1.

Figure 5-3. JF1 Header Pins

Ground x (key)

Power LED

HDD LED

NIC1

NIC2

OH/Fan Fail LED

Power Fail LED

Ground

Ground

20 19

NMI

x (key)

Vcc

Vcc

Vcc

Vcc

Vcc

Vcc

Reset Button

Power Button

21

5-6

Image 40

SUPER MICRO Computer 6014P-TR user manual Connecting the Control Panel, JF1 Header Pins

Contents

Super Manual Revision 1.0a Release Date October 8 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup Bios Preface Table of Contents System Safety Advanced Serverboard Setup Advanced Chassis Setup Bios Appendices Page Chapter Introduction Overview Serverboard Features ProcessorsMemory Serial ATA Server Chassis Features Other FeaturesSystem Power ATI Graphics Controller PCI Expansion Slots Front Control PanelBackplane Cooling System Intel E7520 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-Paciﬁc Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking Tabs Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel Buttons Control Panel LEDs Serial ATA Drive Carrier LED Page Chapter System Safety General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Unpacking Processor and Heatsink Installation CPU Installation Heatsink Installation Pin PGA Socket Empty and with Processor Installed Installing the Heatsink Removing the Heatsink/CPU Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel JF1 Header Pins Installing Memory Dimm Installation Figures 5-5a and 5-5bI/O Ports Memory Support 5a. Side View of Dimm Installation into Slot Memory Speed Jumpers PCI card installation Adding PCI CardsPCI slots 6014P-T Riser Cards Slot Add-on Card Serverboard Details Super X6DHP-TG Layout Connector Description Jumper Description Default SettingX6DHP-TG Quick Reference Connector Deﬁnitions ATX Power ConnectorProcessor Power Connector Power LED NIC1/2 LEDs Power Fail LEDOverheat/Fan Fail LED Power Button UID Button & UID LEDChassis Intrusion JLAN1/2 Ethernet Ports Universal Serial Bus USB0/1 Universal Serial Bus HeadersFan Headers Serial Ports Wake-On-Ring Power LED/SpeakerATX PS/2 Keyboard and PS/2 Mouse Ports SMB Power Connector SMB Jumper Settings VGA Enable/DisableExplanation Jumpers Cmos Clear Sata Enable/Disable Jlan Enable/DisableBios Debug Watch Dog Memory Speed Select Jlan LEDs Onboard IndicatorsUnit Identiﬁer Floppy Connector Floppy and Hard Disk Drive Connections IDE Connectors IDE Drive Connectors Pin Deﬁnitions JIDE#1, JIDE#2Page Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required 6014P-T Control Panel6014P-TR Installing a new fan System FansSystem Fan Failure Replacing System Cooling Fans Drive Bay Installation/Removal Accessing the Drive Bays Serial ATA Drive Installation Mounting a Serial ATA drive in a drive carrier Installing/removing hot-swap Sata drives Removing a Serial ATA Drive Carrier DVD/CD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply 6014P-TR 6014P-T Reconﬁguring the Power Supply Reconﬁguring the 6014P-T see Figure Reconﬁguring the 6014P-TR see Figure Page Reconﬁguring the Power Supply Page Chapter Starting the Setup UtilityIntroduction Main Bios Setup Running SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup FeaturesBios Date System Time Serial ATA RAID Enable Native Mode OperationLegacy Diskette a Parallel ATA Type LBA Mode Control Transfer ModeUltra DMA Mode Multi-Sector Transfer Advanced Setup Boot FeaturesQuick Boot Mode Quiet Boot Power Button Behavior After Power FailureMemory Cache Cache System Bios Area Cache Video Bios Area Cache Base 0-512K Cache Base 512K-640KCache Extended Memory Write Back Reset Conﬁguration Data Discrete Mtrr AllocationPCI Conﬁguration Onboard Glan Gigabit- LAN Oprom Conﬁgure Enable Master Latency TimerLarge Disk Access Mode Force Compliance Mode ECC Error Type Serr Signal ConditionProcessor Power Management USB Function Device Conﬁguration KBC Clock inputOnboard COM1 Base I/O Address Event Logging ECC Event LoggingMark DMI Events as Read Clear All DMI Event Logs Serial Port B ModeParallel Port Interrupt Hardware Monitor Logic CPU Temperature Threshold P1V8 Vdimm Supervisor Password Is User Password IsSecurity N12VScaled Set Supervisor Password Set User PasswordFixed Disk Boot Sector Password on Boot Boot +Removable DevicesCdrom Drive +Hard Drive Load Setup Defaults ExitExit Saving Changes Exit Discarding Changes Save Changes Page Appendix a Bios Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Appendix B Software Installation Conﬁguring Bios settings for the Sata RAID FunctionsAdaptec Embedded Sata RAID Controller Driver Serial ATA Sata Adaptec Embedded Sata with HostRAID Controller Driver Using the Adaptec RAID Conﬁguration Utility ARC Using the Array Conﬁguration Utility ACU Managing Arrays Viewing Array Properties From the ARC menu, select Array Conﬁguration Utility ACUDeleting Arrays ACU Creating Arrays To create an array Assigning Array Properties To assign properties to the new array When ﬁ nished, press Done as shown on the following screen Page Deleting a Bootable Array Adding a Bootable ArrayCtrl+B Adding/Deleting Hotspares To initialize drives Initializing Disk DrivesSelect Initialize Drives Page Rebuilding Arrays To Rebuild an array To access the disk utilities Using the Disk UtilitiesYou can choose from the following options To Exit Adaptec RAID Conﬁguration Utility Installing Intels ICH5R Driver by Adaptec and Windows OS Installing Other Software Programs and Drivers Installing Other Drivers Supero Doctor Figure B-2. Supero Doctor III Health Information Display Figure B-3. Supero Doctor III Remote Control Display Appendix C System Speciﬁcations Weight PFC Power Supply ratings apply to each moduleExpansion Slots Serverboard Operating Environment Regulatory Compliance