Advanced Setup Screen | SUPER MICRO Computer 6113L-i, 6113L-8

Chapter 7: BIOS

7-3 Advanced Setup Screen

Selecting the Advanced tab takes you to the Advanced setup screen. The Advanced BIOS Setup screen and sub menus are listed below:

When you first enter the Advanced Setup screen, the Setup Warning will be displayed. Please follow the instructions and set the correct value for each item to prevent the system from malfunctioning.

!Super IO Configuration

7-3

Image 75

SUPER MICRO Computer 6113L-i, 6113L-8 user manual Advanced Setup Screen, Super IO Configuration

Contents

Super Page Preface About This ManualManual Organization Advanced Serverboard Setup Advanced Chassis SetupBios Preface Table of Contents Advanced Serverboard Setup System Safety Bios Advanced Chassis Setup Appendices Appendix a Bios Error Beep CodesPage Overview Chapter Introduction Chipset Serverboard Features Onboard Controllers/Ports Processors MemoryPCI Expansion Slots ATI Graphics Controller E8870 Chipset Block Diagram Other Features Backplane Server Chassis FeaturesSystem Power Control Panel Cooling System Asia-Pacific Contacting SupermicroHeadquarters EuropePage Chapter Server Installation Preparing for SetupUnpacking the SuperServer 6113L-8/6113L-i Choosing a Setup Location Rack PrecautionsServer Precautions Installing the Server into a Rack Installing the Outer RailsIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing the Server into the Rack Installing the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Control Panel Buttons Chapter System Interface Control Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Electrical Safety Precautions Chapter System Safety General Safety Precautions ESD Precautions Operating Precautions Unpacking Chapter Advanced Serverboard SetupPrecautions Handling the i2DML-8G2/i2DML-iG2 Serverboard Locating the Components Itanium2 Processor and Heatsink Installation Installing Heatsink Retention Mechanism Installing the Heatsink Retention Mechanism Pointer Installing Itanium2 CPUs Pins of the CPU are not Installing the Power PodsCPU power pod Power pod slot Dual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks CPUs 2 with Heatsinks Installed Connecting AC Power Connecting Cables Connecting Data CablesConnecting Power Cables Front Control Panel Header Pins U66 Connecting the Control Panel Installing Memory Dimm Installation See FigureI/O Ports Memory Support 6a. Side View of Dimm Installation into Socket PCI card installation Adding PCI CardsPCI-X slot Super i2DML-8G2 Serverboard Details Jumper Description Default Setting Connector DescriptionI2DML-8G2/i2DML-iG2 Quick Reference Connector Definitions Overheat LED OH HDD LED Reset Button Power ButtonUniversal Serial Bus USB0/1 Chassis Intrusion Front Panel Universal Serial Bus HeaderSerial Ports Glan Ethernet Ports Power Fault Fan HeadersWake-On-Ring SMB SMB Power I2C Connector Cmos Clear Jumper SettingsVGA Enable/Disable Explanation Jumpers Glan Enable/Disable Watch Dog Enable/DisablePower Fail Alarm Enable/ Disable Debug LEDs Onboard IndicatorsScsi Enable/Disable 6113L-8 only Glan LEDs IDE Connectors Scsi and IDE Disk Drive ConnectionsScsi Activity LED 6113L-8 only Pin Ultra 320 Scsi Connectors J3 and J18 Ultra320 Scsi Connectors 6113L-8 only Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Chassis Front and Rear Views Control Panel System Fans System Fan FailureReplacing System Fans Removing the Front Bezel Drive Bay Installation/Removal Removing the Front Bezel Accessing the Drive Bays Mounting a SCSI/IDE drive in a drive carrier SCSI/IDE Drive Installation Installing/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Removing the power supply Power SupplyPower Supply Failure Removing/Replacing the Power Supply Removing/Replacing the Power Supply Introduction Chapter System Time/System Date Main Setup ScreenLanguage Menu BSP Information Super IO Configuration Advanced Setup Screen Serial Port1 Address/Serial Port2 Address IDE Configuration Block Multi-Sector Transfer LBA/Large ModePrimary IDE Master/Slave, Secondary IDE Master/Slave Type Armd Emulation Type DMA ModeA.R.T. For Hard disk drives Bit Data Transfer Bios Settings Configuration Quiet BootAtapi 80-Pin Cable Detection System Health Monitor Watch Dog Timer Value Peripheral Device ConfigurationPower Loss Control Watch Dog Timer USB Configuration USB FunctionLegacy USB Support PCI IDE BusMaster PCI/PnP ConfigurationPCI Latency Timer Allocate IRQ to PCI VGA Hardware Health Monitoring Health Function Security SettingsOverheat Temperature Trips Change Supervisor Password Exit Saving Changes Change User PasswordClear User Password Exit Options Load Optimal Defaults Load Fail-Safe DefaultsDiscard Changes Appendix a Bios Error Beep Codes IA-32 Error Beep CodesBeep Code Error Message Description Checkpoints Code Description IA-64 Common Debug Codes Checkpoint Code Description Appendix B Bios Post Codes Register for date and time next Monochrome mode and color mode settings next 47h 60h 95h Introduction to the EFI Platform Appendix C Software Installation Amibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications System Input Requirements WeightPower Supply System Cooling