Connecting Two Subs | Tannoy ACTIVE STUDIO MONITORS specs

Connecting Two Subs

Two Subs can be connected to any of the above Set-Ups

When no Bass management is selected, no signal will be sent to the subwoofers.

When Bass management is selected, low frequency content from the left channel is extracted and sent to the left subwoofer.

Low frequency content from the right channel is extracted and sent to the right subwoofer.

The iDP™ Remote, iDP SOFT™ or PC-iP™can be connected to any spare TC Link “out” connection.

! REMEMBER – To set a master monitor as the system controller the TC Link button on the rear panel MUST be in the out position.

Connecting Three Subs

Three subs can be connected to any of the above Set-Ups

When no Bass management is selected, no signal will be sent to the subwoofers.

When Bass management is selected, low frequency content from the left channel is extracted and sent to the left subwoofer.

Low frequency content from the right channel is extracted and sent to the right subwoofer. Low frequency content from the centre channel is extracted and sent to the centre subwoofer.

The iDP™ Remote, iDP SOFT™ or PC-iP™can be connected to any spare TC Link “out” connection.

! REMEMBER – To set a master monitor as the system controller the TC Link button on the rear panel MUST be in the out position.

23

Image 23

Tannoy ACTIVE STUDIO MONITORS owner manual Connecting Two Subs, Connecting Three Subs

Contents

Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design Philosophy Tannoy WideBand SuperTweeter High efficiency compact Switched Mode Power Supply SmpsUnpacking & Visual Checks Orientation Speaker PlacementPreliminary Recommendation Master & Slave Concept IDP Soft Software Remote Remote ControlSlave Monitor & Subwoofer Initializing the Network Slave/Subwoofer Master Unit SUB IDP Display Master General Setup Procedure Analog Stereo Set-up With Mono Subs SetupsGeneral Setup Procedure Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo Subs Digital Set-up Analog Set-up Digital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-up Connecting Three Subs Connecting Two Subs Stereo Set-up With Chains on L&R. Analog or Digital Dig/6 Master Setup when the monitors are connected Select Monitor Tasks Reset ProcedureReset All Settings Select Setup † PC-iP Press Enter to access the Select ModeParameter Description Main Display LFE Gain PhaseBass Management LFE Low Pass Filter External Clock Setup MenuSetup Set Monitor Task LFE channel important Parameters available for the subwoofer Parameter Categories IDP Remote MUTE/UNMUTE Solo keys for the channels R LS- SUB RS Preset 1/3 and 2/4 keysVolume potentiometer REF Level keys Minimum requirements Installation on PCInstallation on Mac IDP Soft Bass Mgt Bass Management Volume ControlREF LEV. keys Monitor and Sub icons Locked symbol in Preset List IDP Soft Preset ListRecall presets Store presets Upload Software to Monitors IDP Soft Network BNC Sync System Setup ConfigurationAnalog Gain Calibrate Main Monitors Monitor Assignment Calibrate Subwoofer LFE Low Pass Filter Phase RangeLFE Gain Range 0 to 14dB Chained monitors System Master & Slaves Technical Specifications Precision 6 iDP Technical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP Subwoofer Dimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/Silver IDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog Input SUB LFE Serial to Cat-5 cable CablesTC Link Standard Cat-5 cables AES/EBU Standard cables Declaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December