Volume Control, REF LEV. keys | Tannoy ACTIVE STUDIO MONITORS

iDP SOFT™ (cont.)

This is the Main screen from where all other iDP SOFT™ screens are accessed.

When The (((•))) network icon (upper left corner)

Is steady - The computer running the iDP SOFT™ is not correctly connected to Precision iDP™ monitors. Check connections, cables and refer to the setup-illustrations on pages 16-24 in this manual.

Is blinking - The computer is correctly connected to your Precision iDP™ system.

The ((())) icon is also used to access the Network screen.

Press ((())) to access.

VOLUME Control

Use the mouse on the VOLUME control on the middle of the display to adjust the volume

REF LEV. keys

The three keys below the volume control allow access to the 3 user-defined Reference level settings. To change these Ref. Levels:

Set the volume control to the desired position.

Hold cursor above Ref. Level key and select “Store” from the pop-up icons appearing.

Monitor and Sub icons

Appropriate icons as illustrated above will indicate Precision iDP™ monitors and subs. Press to access specific parameters for the monitors.

This symbol in the Main screen indicates that the selected setup expects a monitor at a certain position but no monitor is found. Check your connections and retry.

Bass Mgt - Bass Management

Indicates the selected Cross-over frequency for Bass Management.

Tools

When placing the cursor on top of a monitor, a few tools will appear:

Press this symbol to enter calibration pages

Press to mute the monitor

Press to solo the monitor

35

Image 35

Tannoy ACTIVE STUDIO MONITORS Volume Control, REF LEV. keys, Monitor and Sub icons, Bass Mgt Bass Management, Tools

Contents

Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design Philosophy Tannoy WideBand SuperTweeter High efficiency compact Switched Mode Power Supply SmpsUnpacking & Visual Checks Orientation Speaker PlacementPreliminary Recommendation Master & Slave Concept IDP Soft Software Remote Remote ControlSlave Monitor & Subwoofer Initializing the Network Slave/Subwoofer Master Unit SUB IDP Display Master General Setup Procedure Analog Stereo Set-up With Mono Subs SetupsGeneral Setup Procedure Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo Subs Digital Set-up Analog Set-up Digital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-up Connecting Three Subs Connecting Two Subs Stereo Set-up With Chains on L&R. Analog or Digital Dig/6 Master Setup when the monitors are connected Select Monitor Tasks Reset ProcedureReset All Settings Select Setup † PC-iP Press Enter to access the Select ModeParameter Description Main Display LFE Gain PhaseBass Management LFE Low Pass Filter External Clock Setup MenuSetup Set Monitor Task LFE channel important Parameters available for the subwoofer Parameter Categories IDP Remote MUTE/UNMUTE Solo keys for the channels R LS- SUB RS Preset 1/3 and 2/4 keysVolume potentiometer REF Level keys Minimum requirements Installation on PCInstallation on Mac IDP Soft Bass Mgt Bass Management Volume ControlREF LEV. keys Monitor and Sub icons Locked symbol in Preset List IDP Soft Preset ListRecall presets Store presets Upload Software to Monitors IDP Soft Network BNC Sync System Setup ConfigurationAnalog Gain Calibrate Main Monitors Monitor Assignment Calibrate Subwoofer LFE Low Pass Filter Phase RangeLFE Gain Range 0 to 14dB Chained monitors System Master & Slaves Technical Specifications Precision 6 iDP Technical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP Subwoofer Dimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/Silver IDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog Input SUB LFE Serial to Cat-5 cable CablesTC Link Standard Cat-5 cables AES/EBU Standard cables Declaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December