IDP Soft, Installation on PC | Tannoy ACTIVE STUDIO MONITORS

A C T I V E S T U D I O M O N I T O R S

iDP SOFT™

iDP SOFT™ is a software editor for the Precision iDP™ monitors. All parameters that can be controlled using the display on the System Controller can be controlled using the iDP SOFT™ program.

Installation on PC:

Place the Installation CD in your CD ROM drive and open CD contents.

Press Setup

Follow the instructions.

Installation on Mac:

Enter the Installation CD in your CD ROM drive and open CD contents.

Run the installer.

Follow the instructions.

Minimum requirements

PC Pentium 2 running Windows 95/98, 2000 or a Mac running OS X 64MB RAM

800x600 24bit screen resolution

1 free Serial port or USB. Connect from Serial or USB port to any free TC LINK connection on your Precision iDP™ monitors using ONLY the cables described on page cables page (Appendix).

A Serial to Cat-5 cable is supplied, if a USB port is used, an optional "USB to Serial Port" converter will be required. The "KeySpan USA 19" has been tested by Tannoy and found appropriate.

For further information please visit www.keyspan.com or contact Tannoy customer support.

Press to enter preset list

34

Image 34

Tannoy ACTIVE STUDIO MONITORS owner manual IDP Soft, Installation on PC, Installation on Mac, Minimum requirements

Contents

Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Concept & Design Philosophy Tannoy Dual Concentric Unpacking & Visual Checks High efficiency compact Switched Mode Power Supply SmpsTannoy WideBand SuperTweeter Preliminary Recommendation Speaker PlacementOrientation Master & Slave Concept Initializing the Network Remote ControlSlave Monitor & Subwoofer IDP Soft Software Remote Master Unit Slave/Subwoofer SUB General Setup Procedure IDP Display Master General Setup Procedure SetupsAnalog Stereo Set-up With Mono Subs Analog Stereo Set-up With Stereo Subs Stereo Digital Set-up With Mono Subs Analog Set-up Digital Set-up Digital 192kHz Set-up Digital Set-up Analog Set-up Alternative 7.1 Set-up Analog, Digital& 192kHz Connecting Two Subs Connecting Three Subs Dig/6 Master Stereo Set-up With Chains on L&R. Analog or Digital Setup when the monitors are connected Select Setup Reset ProcedureReset All Settings Select Monitor Tasks Main Display Press Enter to access the Select ModeParameter Description † PC-iP LFE Low Pass Filter PhaseBass Management LFE Gain Set Monitor Task Setup MenuSetup External Clock Parameters available for the subwoofer LFE channel important Parameter Categories IDP Remote REF Level keys Preset 1/3 and 2/4 keysVolume potentiometer MUTE/UNMUTE Solo keys for the channels R LS- SUB RS IDP Soft Installation on PCInstallation on Mac Minimum requirements Monitor and Sub icons Volume ControlREF LEV. keys Bass Mgt Bass Management Store presets IDP Soft Preset ListRecall presets Locked symbol in Preset List IDP Soft Network Upload Software to Monitors Analog Gain System Setup ConfigurationBNC Sync Monitor Assignment Calibrate Main Monitors Calibrate Subwoofer LFE Gain Range 0 to 14dB Phase RangeLFE Low Pass Filter Chained monitors Technical Specifications Precision 6 iDP System Master & Slaves Technical Specifications- Precision 8 iDP Technical Specifications TS212 iDP Subwoofer TS112 iDP Subwoofer & iDP Dimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS212 iDP Grey/Silver Dimensions Precision TS112 iDP Grey IDP Display Messages System Delays Sample Rate Digital Input Analog Input Curves Explained SUB LFE AES/EBU Standard cables CablesTC Link Standard Cat-5 cables Serial to Cat-5 cable Declaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December