Parameter Categories | Tannoy ACTIVE STUDIO MONITORS instruction

Parameter Categories

Global Parameters

These parameters apply to the entire system: -

Global parameters stored with presets

•Bass Management

•Mute Status

Global parameters NOT stored with presets

•Ref. Levels

•Analog Input Sensitivity

•Selected Setup

•BNC Sync

Local Parameters

These parameters apply to individual Precision monitors: -

Local parameters stored with presets

•X-Curve

•Parametric EQ setting (set via optional PC-iP™)

•LFE Gain (subs)

•LFE Low Pass (subs)

•Rel. Level

Local parameters NOT stored with presets

•Bass and Treble

•Delay

•Lock status (set via optional PC-iP™)

•Room position

•Calibration Level

•Tasks

•Phase (Subs)

•Polarity (Subs)

Recall

•Press ENTER and use ARROW keys to select presets

•Press ENTER to recall/load the selected preset

If no user-preset are stored on locations 1 to 4, presets 16 to 19 are loaded instead.

Complete preset list is available on page 52.

Store

•Press ENTER and select storage location using the ARROW keys

•Press ENTER again to store.

Storage location can be 1-15.

Parameter can be locked via the optional PC-iP™Installers software. When trying to change values on a locked parameter the LCD display reads “Locked”.

31

Image 31

Tannoy ACTIVE STUDIO MONITORS owner manual Parameter Categories

Contents

Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design Philosophy Unpacking & Visual Checks High efficiency compact Switched Mode Power Supply SmpsTannoy WideBand SuperTweeter Preliminary Recommendation Speaker PlacementOrientation Master & Slave Concept IDP Soft Software Remote Remote ControlSlave Monitor & Subwoofer Initializing the Network Slave/Subwoofer Master Unit SUB IDP Display Master General Setup Procedure General Setup Procedure SetupsAnalog Stereo Set-up With Mono Subs Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo Subs Digital Set-up Analog Set-up Digital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-up Connecting Three Subs Connecting Two Subs Stereo Set-up With Chains on L&R. Analog or Digital Dig/6 Master Setup when the monitors are connected Select Monitor Tasks Reset ProcedureReset All Settings Select Setup † PC-iP Press Enter to access the Select ModeParameter Description Main Display LFE Gain PhaseBass Management LFE Low Pass Filter External Clock Setup MenuSetup Set Monitor Task LFE channel important Parameters available for the subwoofer Parameter Categories IDP Remote MUTE/UNMUTE Solo keys for the channels R LS- SUB RS Preset 1/3 and 2/4 keysVolume potentiometer REF Level keys Minimum requirements Installation on PCInstallation on Mac IDP Soft Bass Mgt Bass Management Volume ControlREF LEV. keys Monitor and Sub icons Locked symbol in Preset List IDP Soft Preset ListRecall presets Store presets Upload Software to Monitors IDP Soft Network Analog Gain System Setup ConfigurationBNC Sync Calibrate Main Monitors Monitor Assignment Calibrate Subwoofer LFE Gain Range 0 to 14dB Phase RangeLFE Low Pass Filter Chained monitors System Master & Slaves Technical Specifications Precision 6 iDP Technical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP Subwoofer Dimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/Silver IDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog Input SUB LFE Serial to Cat-5 cable CablesTC Link Standard Cat-5 cables AES/EBU Standard cables Declaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December