Setup Menu, Set Monitor Task | Tannoy ACTIVE STUDIO MONITORS

Setup Menu

Press ENTER to access sub-menus

Setup

Press ENTER to access select mode. Select mode is indicated by “ * ”

Press ENTER to confirm choice

Empty

Custom Stereo Analog Stereo Digital Stereo 192kHz Surround Analog Surround Digital Surround 192kHz 5.1 dig/6 Master

Set Monitor Task

For the System Controller/Master monitor to identify and operate all monitors in the setup, each monitor must be given one of the following tasks indicating function and position.

No Task	L SUB
L Front	R SUB
R Front	LS Chain
Center	RS Chain
(C) SUB	L Inner
L Sur	R Inner
R Sur	Custom 1-4 (Reserved for future use)
C Sur

Press ENTER to access task options

Use ARROW keys to select task

Press ENTER to confirm selected task

External Clock

Press ENTER to access sub-menus

BNC Sync On:

The monitor attempts to lock on the word Clock BNC.

BNC Sync Off:

The monitor will attempt to lock on the AES Input.

Calibrate Monitor

Press ENTER

Select monitor to calibrate using the ARROW keys

Press ENTER

29

Image 29

Tannoy ACTIVE STUDIO MONITORS owner manual Setup Menu, Set Monitor Task, External Clock

Contents

Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design Philosophy Tannoy WideBand SuperTweeter High efficiency compact Switched Mode Power Supply SmpsUnpacking & Visual Checks Orientation Speaker PlacementPreliminary Recommendation Master & Slave Concept Slave Monitor & Subwoofer Remote ControlInitializing the Network IDP Soft Software Remote Slave/Subwoofer Master Unit SUB IDP Display Master General Setup Procedure Analog Stereo Set-up With Mono Subs SetupsGeneral Setup Procedure Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo Subs Digital Set-up Analog Set-up Digital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-up Connecting Three Subs Connecting Two Subs Stereo Set-up With Chains on L&R. Analog or Digital Dig/6 Master Setup when the monitors are connected Reset All Settings Reset ProcedureSelect Setup Select Monitor Tasks Parameter Description Press Enter to access the Select ModeMain Display † PC-iP Bass Management PhaseLFE Low Pass Filter LFE Gain Setup Setup MenuSet Monitor Task External Clock LFE channel important Parameters available for the subwoofer Parameter Categories IDP Remote Volume potentiometer Preset 1/3 and 2/4 keysREF Level keys MUTE/UNMUTE Solo keys for the channels R LS- SUB RS Installation on Mac Installation on PCIDP Soft Minimum requirements REF LEV. keys Volume ControlMonitor and Sub icons Bass Mgt Bass Management Recall presets IDP Soft Preset ListStore presets Locked symbol in Preset List Upload Software to Monitors IDP Soft Network BNC Sync System Setup ConfigurationAnalog Gain Calibrate Main Monitors Monitor Assignment Calibrate Subwoofer LFE Low Pass Filter Phase RangeLFE Gain Range 0 to 14dB Chained monitors System Master & Slaves Technical Specifications Precision 6 iDP Technical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP Subwoofer Dimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/Silver IDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog Input SUB LFE TC Link Standard Cat-5 cables CablesAES/EBU Standard cables Serial to Cat-5 cable Declaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December