Using the Strap | The Speaker Company M23 manual

2.2 Using the Strap

2.2.1 Hand Strap

1.Clip both rings of the hand strap onto the strap buttons by placing each O-ring over the strap button and gently pulling up on the strap until the strap until the strap locks into place.

Hand strap

Strap button

O -rings

7

Image 10

The Speaker Company M23 user manual Using the Strap, Hand strap Strap button Rings

Contents

USER’S Manual Contents Update Firmware Via Serial Port Update Firmware Via USB Port Printer initialization Ignore AUTO.BAS Compliances Copyright DeclarationWichtige Sicherheits-Hinweise Documentation Equipment ChecklistIntroduction Unpacking and Inspection Front View Tear plate for label Peel roller Tear bar for liner Peel barPage Rear View Getting Started Install the BatteryLi-ion battery Release button Supply door Release button Using the Strap Hand strap Strap button Rings Shoulder Strap Option Shoulder strap Roll of supplies Supply holder tabs Release button Loading MediaLabel Supply door Peel off enablers Peel roller Paper exit chute Loading Die-cut Labels Roll of label Supply holder tabs Release button Peel roller Peeler bar Tear edge for liner Liner Label Liner Loading Fan-fold Labels Paper core Fan-fold paper entrance chute Fan-fold media Paper guides RS232 port Connecting the Communication CableHinged Cable door Screws RS232 port Cable cavity Null modem cable Using the Bluetooth Wireless Optional Hinged cable door Bluetooth Status LED Power LED Description Charging the BatteryBattery Power Status LEDPage Navigation buttons LCD display On/Off button Using the Display and ButtonsLCD Display and Buttons Icon Description LCD Display Icon Description LCD/Keyboard Operation Option LCD Menu Overview SWI Main Menu Setup File ManagerPause Speed Ips SetupSpeed Density DensityDirection Direction Offset Batch Mode Peeler ModePrint Mode Tear Off Mode/Batch Mode/Peeler Mode Reference X & Reference Y 850 001 002 Gap Sensor Gap Sensor Bline SensorAuto Gap Manual Gap Auto Gap GAP Calibrate Insert liner Then hit EnterCalibrating Stock AD = Gap Sensor Stock AD = Intension = Manual Gap Bline Calibrate Auto Bline Manual BlineInsert label Then hit Enter Black Sensor Manual Bline Continuous Calibrate 9600 bps 19200 bps Calibrate 100None Odd 8 Data Bits Exit One Stop Bit Two Stop Bits 00A0F8E2AD9E Protocol TCP State Unknow Radio Ieee 802.11b Status ConfigureVersion 1.2 M23 WiFi TSC Wireless IP Address Subnet Mask Subnet Mask 000.000.000.000 IP Address 000.000.000.000Gateway 000.000.000.000 Protocol PSP3Port +09100 Ssid Escape Char +035 Save Settings? Are you sure?Reset Escape Char Security Disable ExitChange PIN 0000 Change PIN Local Name Local Name BT23Contract Information Low Power Disable EnableDisable 10 Seconds Backlight File Manager Disable 5 MinutesShut Down Dram 256 KB Free FLASH3072 KB Free Diagnostics To print out the self test data to a label Battery Voltage = 7.33 Display Display Buttons Language English Exit Initialization Mileage Info ServiceDefault setting Parameter Mileage 6m Labels 53pcs Connect by Radio Optional Printing LabelsConnect with a Cable to Print Ready RF Network Stand-along PrintingBefore Stand-along Download the Format Recovery Procedure TroubleshootingProblem No Power Not Printing No Paper Possible Cause Start Stand-along Printing Poor Print Quality Reduced Battery lifePaper Jam Interval MaintenancePrinter Part Print Head Platen Roller Peel Roller Method Tear Bar/Peel Bar Sensor Exterior Interior Illustration for recommended cleaning parts Page Firmware Update Procedure Update Firmware Via Serial PortPage Page Update Firmware Via USB Port Power on utilities Printer initialization Initializing Ignore AUTO.BAS Ignore AUTO.BASPage No.35, Sec , Ligong 1st Rd., Wujie Township