13.4. Input Parameter Setting

13.4.1. Setting flow chart

[Normal matrix operation]

Normal use state

MEMORY UTILITY

Press for over 2 seconds.

PARAMETER Setting menu screen

 

 

 

 

Input channel selection

 

I N P U T – S E T T I N G

 

 

 

 

 

S E L E C T I N P U T C H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT SELECT 1 – 8

ESC/BACK

Input channel name setting (p. 42-A1)

I N 1 – _ _ _ _ _ _ _

(For the channel on which the D-001T is used)

(For the channel on which the ZP-001T is used)

 

Input sensitivity setting (p. 42-A2)

Pre-paging tone ON/OFF setting (p. 43-A5)

 

 

 

 

 

 

I N 1 – S E N S I T I V I T Y – 1 0

 

 

P R E P A G E T O N E – O F F

 

 

 

 

 

 

 

(For the channel on which the AN-001T is used)

ANC operation ON/OFF setting

 

PARAMETER

 

 

 

 

(When the ANC operation is set

 

 

 

(When the ANC operation is set

to BYPASS) (p. 43-A7)

 

 

 

to ACTIVE) (p. 43-A7)

 

 

 

 

 

A N C B Y P A S S

 

 

 

A N C A C T I V E

 

 

 

 

 

Phantom power ON/OFF setting (p. 42-A3)

Operation mode setting (p. 43-A6)

I N 1 – P H A N T O M – O F F

M O D E = P A G I N G P O R T

Input sensitivity setting (p. 42-A2)

I N 1 – S E N S I T I V I T Y – 1 0

VOX ON/OFF setting (p. 42-A4)

I N 1 – V O X – O F F

The screen display examples shown above may differ from actual displays.

The on-screen indications shown in red here (actually shown by flashing cursors) are parameters or setting contents to be selected with the Parameter setting knob, input channel selection key or other designated keys.

The indications of the [], [], [], and [] arrows represent that the screen is switched with the Screen shift key.

Use the Parameter setting knob for each parameter selection.

Phantom power ON/OFF setting (p. 42-A3)

I N 1 – P H A N T O M – O F F

ANC-activated output setting (p. 43-A8)

A N C A P P L I E S O U T 1

 

 

 

 

 

 

 

(When Monitor function is ON)

 

 

 

 

 

 

 

 

 

 

 

 

Monitor output channel selection

 

 

 

 

 

Monitor ON/OFF setting (p. 43-A9)

 

 

(p. 44-A10)

 

 

 

 

 

 

 

 

M O N I T O R O U T – O F F

 

 

 

 

 

M O N I T O R O U T O U T 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(For the channel on which the AN-001T is not used)

Priority setting (p. 44-A12)

I N 1

P R I O R I T Y 8

Note

 

 

 

Set the priority level higher than level 8 for

 

 

 

the input channel to be used for broadcast

 

 

 

 

 

 

 

 

 

(e.g. paging using the ZP-001T) that

 

 

 

 

 

 

overrides BGM broadcasts.

 

 

 

Ducker ON/OFF setting (p. 44-A13)

I N 1 – D U C K E R O F F

40

Input channel name setting