Port Forwarding | Topcom WBR 7101GMR specification

2.6.1 Port Forwarding

The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a particular LAN IP address. It help you to host some servers behind the router NAT firewall.

Parameter	Description

Enable Port Forwarding	Enable Port Forwarding
Private IP	This is the private IP of the server behind the
	NAT firewall.
	Note: You need to give your LAN PC clients a
	fixed/static IP address for Port Forwarding to
	work properly.
Type	This is the protocol type to be forwarded. You
	can choose to forward “TCP” or “UDP” packets
	only or select “both” to forward both “TCP” and
	“UDP” packets.
Port Range	The range of ports to be forward to the private IP.
Comment	The description of this setting.
Add Port Forwarding into the table	Fill in the "Private IP", “Type”, “Port Range” and
	"Comment" of the setting to be added and then
	click "Add". Then this Port Forwarding setting
	will be added into the "Current Port Forwarding
	Table" below. If you find any typo before adding

62

Image 62

Topcom WBR 7101GMR manual Parameter Description Enable Port Forwarding

Contents

Skyr@cer WBR 7101gmr Minimum Requirements Setup DiagramIntroduction Get to know the Broadband Router Appendix a Glossary Features Package Content Local Area Network LAN ResetGet to know the Broadband Router Back Panel Wide Area Network WAN WAN 10/100M Front PanelLight Status Description Off Below shows a typical setup for a Local Area Network LAN Getting started Configure your PC to obtain an IP address automaticallyDNS Configuration Select Disable DNS 2a Windows 95/98/Me 2b Windows XP 2c Windows 2d Windows NT IP Address Select Obtain an IP address from a Dhcp server Quick Setup Wizard Chapter Menu Description Quick Setup Wizard ChapterGeneral Setup Chapter Status Information Chapter Tools Chapter Logout End Daylight Savings Time Enable Daylight SavingsTime Server Address Click on Next to proceed to the next page Broadband Type Parameters Description Host Name MAC Address Subnet Mask Parameters DescriptionGateway IP Parameter Description User Name PasswordService Name If you select Manual, the router will connect to ISP only When you click Connect manually from the Web userTo the idle timeout. If the WAN line breaks down and latter Interface. The WAN connection will not disconnected due Gateway User ID Connection ID This is the ID given by ISP. This is optional Select this item if you are using the service provided byPptp Gateway Bezeq in Israel L2TP Router When YOU Finished Using the Internet L2TP GatewayPage Enter the User Name provided by your ISP for the Telstra Big LAN Menu Description SystemWAN Firewall System End Daylight Savings Time Parameters Description Current Password New Password Parameters Description Host Address Port Port number of remote management web interface Enabled Your ISP has given you an IP address already Dynamic IP Parameters Description Domain Name Server DNS Server Secondary DNS Address optional Provider Parameters Default Description Enable/DisablePassword/Key Domain name IP Subnet Mask Parameters Default Description802.1d Spanning Tree Disabled Dhcp Server To End IP 192.168.1.199. If you Lease TimeIP Address Pool Wireless module Function AP Mode setting AP Bridge-Point to Point mode setting AP Bridge-Point to Multi-Point mode setting Parameters Default Description Mode BandPage Fragment Threshold specifies the maximum Broadcast Essid Data RatePreamble Type CTS Protection Key Format Ascii Characters guest 3.2 802.1x only 3.3 802.1x WEP Static key Wpatkip Page WPA Radius QoS Page Bandwidth Edit QoS RuleParameters Description Rule Name Local Port Range ResetLocal IP Address Remote IP Address Virtual Server UPnP SettingParameter Description Port Forwarding ALG Setting Static Routing Parameter Description Enable Port Forwarding It and want to retype again, just click Clear Type Parameters Description Enable Virtual Server Private IPPrivate Port Address host in your LAN Example Virtual Server Special Applications Example Comment Description of this settingExample Special Applications Page UPnP Settings ALG Settings Static Routing Page Parameters Description Access Control 4 DMZ Filter client PCs by IP Fill IP Filtering Table to filter PC clients by IPPage Add PC Page Example Access Control URL Blocking Discard Ping From WAN Intrusion Detection FeaturePing of Death Port Scan Client PC IP Address Parameters Description Enable DMZ Enable/disable DMZPublic IP Address System Log ParametersDescriptionDevice Status Security Log Parameters Description Information Parameters Description Internet Connection Primary DNS and Secondary DNS being used Parameters Description Device Status Parameters Description System Log Parameters Description Security Log Parameters Description Active Dhcp Client Statistics You can reset the router’s system should any problem exist Parameters Description Configuration Tools Parameters Description Firmware Upgrade Reset Parameters Description Reset How to Manually find your PC’s IP and MAC address Appendix a Glossary TCP FTP Smtp POP3