Manuals / Topcom / Computer Equipment / Network Router

Topcom WBR 7101GMR manual UPnP Settings, Parameters, Default, Description, UPnP Feature

Models: WBR 7101GMR

1 98

Download 98 pages 44.71 Kb

Page 70

UPnP Feature

2.6.4 UPnP Settings

With UPnP, all PCs in you Intranet will discover this router automatically. So you do not have to do any configuration for your PC and can access the Internet through this router easily.

Parameters	Default	Description

UPnP Feature	Disable	You can Enable or Disable UPnP feature here.
		After you enable the UPnP feature, all client
		systems that support UPnP, like Windows XP,
		can discover this router automatically and
		access the Internet through this router without
		any configuration. The NAT Traversal function
		provided by UPnP can let applications that
		support UPnP smoothly connect to Internet sites
		without any incompatibility problem due to the
		NAPT port translation.

Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)

70

Image 70

Topcom WBR 7101GMR manual UPnP Settings, Parameters, Default, Description, UPnP Feature

Contents

Skyr@cer WBR 7101gmr Full User GuideFront Panel Package ContentFeatures Getting startedReset Introduction 1 Local Area Network LAN 3 ResetGet to know the Broadband Router Back Panel 2 Wide Area Network WANFront Panel Setup Diagram Figure 1.2 below shows a typical setup for a Local Area Network LANx WINS Configuration Select Disable WINS Resolution Configure your PC to obtain an IP address automaticallyx DNS Configuration Select Disable DNS 2a Windows 95/98/Me2b Windows XP 2c Windows 3 In the Local Area Connection window, click the Properties button2d Windows NT x IP Address Select Obtain an IP address from a DHCP server Quick Setup Wizard Chapter Status Information Chapter General Setup ChapterAddress Mapping, Virtual Server, Access Tools ChapterTools Chapter LogoutSet Time Zone ChapterStart Daylight Savings Time Click on NEXT to proceed to the next page step 2 Broadband Type If your ISP requires a Host Name, type in the host name This is the IP address that your ISP has given you 1.3 PPPoE If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web userto the idle timeout. If the WAN line breaks down and latter interface. The WAN connection will not disconnected due1.4 PPTP Password 1.5 L2TP THE ROUTER WHEN YOU FINISHED USING THE INTERNET Page Parameter Password1.6 Telstra Big Pond DescriptionChapter This section allows you to set the Broadband router’s systemWireless 2.1 System DescriptionParameter 2.1.2 Password Settings2.1.1 Time Zone DescriptionNew Password Confirmed PasswordCurrent Password ParametersHost Address ParametersDescription management/configuration access to the Broadband router from aEnabled Select “Enabled” to enable the remote management functionDescription 2.2 WANYour ISP has given you an IP address already Choose the Dynamic IP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name, Domain Name and MAC address see chapter 1 “Cable Modem” for more detail Description 2.2.7 DNSParameters Domain Name Server DNS ServerPassword/Key DefaultEnable/Disable 2.2.8 DDNS192.168.1.1 Domain Name Lease TimeIP Address Pool 192.168.1.100 to End IP 192.168.1.199. If you2.4 Wireless AP Mode setting Page AP Bridge-Point to Point mode setting page AP Bridge-Point to Multi-Point mode setting page AP Bridge-WDS mode setting page Set Security size of packet during the fragmentation of data 2.4.2 Advanced SettingsFragment Threshold specifies the maximum to be transmitted. If you set this value too low, itBroadcast ESSID Data RatePreamble Type CTS ProtectionYou can select the WEP key length for transmitted in the wireless network. Fill the text Default KeyOnly the key you select it in the Default key will ASCII Characters guest2.4.3.2 802.1x only IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. This mode also uses WEP to encrypt the data during communication 2.4.3.4 WPA Pre-shared key Pre-shared Key The Pre-shared key is used to authenticate andencrypt data transmitted in the wireless network Fill the text box by following the rules below2.4.3.5 WPA Radius 2.4.4 Access Control 2.5 QoSEnable/Disable QoS Add a QoS rule into the table Edit QoS Rule Local Port Range ResetLocal IP Address Remote IP Address2.6 NAT 2.6.5 ALG Setting 2.6.6 Static RoutingPrivate IP Forwarding settings from the table, just click settings from the Current Port ForwardingTable, select the Port Forwarding settings you Delete All button. Click Reset will clear yourThis is the LAN client/host IP address that the Public Port Public Port Example Virtual Server Enable Trigger Port Example Special Applications ExamplePage UPnP Feature 2.6.4 UPnP SettingsDefault Parameters2.6.5 ALG Settings 2.6.6 Static Routing Interface The Broadband routers firewall can block common hacker 2.7 Firewallattacks and can log the attack activities If you want to restrict users from accessing certain Internet applications/services e.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services Page Add PC Page Example Access Control 2.7.2 URL Blocking Parameters 2.7.3 DoS Denial of ServiceIntrusion Detection Feature Description2.7.4 DMZ Enable DMZEnable/disable DMZ ParametersChapter View the Broadband router’s current setting statusView any attempts that have been made to illegally gain access View the Broadband router’s system log3.1 Status and Information 3.2 Internet Connection the Primary DNS and Secondary DNS being used3.3 Device Status View the operation log of the system This page shows the current system log of the Broadband router3.5 Security Log This page shows all DHCP clients LAN PCs currently updated situation3.6 Active DHCP Client connected to your network. The “Active DHCP Client Table”3.7 Statistics StatisticsLAN and Wireless LAN Shows the counters of packets sent and received on WANYou can reset the router’s system should any problem exist Chapter4.1 Configuration Tools This page allows you to upgrade the router’s firmware 4.3 Reset How to Manually find your PC’s IP and MAC address Appendix AGlossary Port Number ApplicationProtocol Telnet