Manuals / Topcom / Computer Equipment / Network Router

Topcom WBR 7101GMR Lease Time, IP Address Pool, Domain Name, to End IP 192.168.1.199. If you

Models: WBR 7101GMR

1 98

Download 98 pages 44.71 Kb

Page 40

Lease Time

	want the router to be your LAN client’s default
	gateway
Lease Time	The DHCP when enabled will temporarily give
	your LAN clients an IP address. In the Lease
	Time setting you can specify the time period that
	the DHCP lends an IP address to your LAN
	clients. The DHCP will change your LAN client’s
	IP address when this time threshold period is
	reached
IP Address Pool	You can select a particular IP address range for
	your DHCP server to issue IP addresses to your
	LAN Clients.
	Note: By default the IP range is from: Start IP
	192.168.1.100 to End IP 192.168.1.199. If you
	want your PC to have a static/fixed IP address
	then you’ll have to choose an IP address outside
	this IP address Pool
Domain Name	You can specify a Domain Name for your LAN

Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)

40

Image 40

Topcom WBR 7101GMR manual Lease Time, IP Address Pool, Domain Name, to End IP 192.168.1.199. If you

Contents

Skyr@cer WBR 7101gmr Full User GuidePackage Content FeaturesFront Panel Getting startedReset Introduction 3 Reset Get to know the Broadband Router Back Panel1 Local Area Network LAN 2 Wide Area Network WANFront Panel Setup Diagram Figure 1.2 below shows a typical setup for a Local Area Network LANConfigure your PC to obtain an IP address automatically x DNS Configuration Select Disable DNSx WINS Configuration Select Disable WINS Resolution 2a Windows 95/98/Me2b Windows XP 2c Windows 3 In the Local Area Connection window, click the Properties button2d Windows NT x IP Address Select Obtain an IP address from a DHCP server Quick Setup Wizard Chapter General Setup Chapter Address Mapping, Virtual Server, AccessStatus Information Chapter Tools ChapterTools Chapter LogoutSet Time Zone ChapterStart Daylight Savings Time Click on NEXT to proceed to the next page step 2 Broadband Type If your ISP requires a Host Name, type in the host name This is the IP address that your ISP has given you 1.3 PPPoE when you click “Connect” manually from the Web user to the idle timeout. If the WAN line breaks down and latterIf you select “Manual”, the router will connect to ISP only interface. The WAN connection will not disconnected due1.4 PPTP Password 1.5 L2TP THE ROUTER WHEN YOU FINISHED USING THE INTERNET Page Password 1.6 Telstra Big PondParameter DescriptionChapter This section allows you to set the Broadband router’s systemWireless 2.1 System Description2.1.2 Password Settings 2.1.1 Time ZoneParameter DescriptionConfirmed Password Current PasswordNew Password ParametersParameters DescriptionHost Address management/configuration access to the Broadband router from aEnabled Select “Enabled” to enable the remote management functionDescription 2.2 WANYour ISP has given you an IP address already Choose the Dynamic IP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name, Domain Name and MAC address see chapter 1 “Cable Modem” for more detail 2.2.7 DNS ParametersDescription Domain Name Server DNS ServerDefault Enable/DisablePassword/Key 2.2.8 DDNS192.168.1.1 Lease Time IP Address PoolDomain Name 192.168.1.100 to End IP 192.168.1.199. If you2.4 Wireless AP Mode setting Page AP Bridge-Point to Point mode setting page AP Bridge-Point to Multi-Point mode setting page AP Bridge-WDS mode setting page Set Security 2.4.2 Advanced Settings Fragment Threshold specifies the maximumsize of packet during the fragmentation of data to be transmitted. If you set this value too low, itData Rate Preamble TypeBroadcast ESSID CTS ProtectionYou can select the WEP key length for Default Key Only the key you select it in the Default key willtransmitted in the wireless network. Fill the text ASCII Characters guest2.4.3.2 802.1x only IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. This mode also uses WEP to encrypt the data during communication 2.4.3.4 WPA Pre-shared key The Pre-shared key is used to authenticate and encrypt data transmitted in the wireless networkPre-shared Key Fill the text box by following the rules below2.4.3.5 WPA Radius 2.4.4 Access Control 2.5 QoSEnable/Disable QoS Add a QoS rule into the table Edit QoS Rule Reset Local IP AddressLocal Port Range Remote IP Address2.6 NAT 2.6.5 ALG Setting 2.6.6 Static RoutingPrivate IP settings from the Current Port Forwarding Table, select the Port Forwarding settings youForwarding settings from the table, just click Delete All button. Click Reset will clear yourThis is the LAN client/host IP address that the Public Port Public Port Example Virtual Server Enable Trigger Port Example Special Applications ExamplePage 2.6.4 UPnP Settings DefaultUPnP Feature Parameters2.6.5 ALG Settings 2.6.6 Static Routing Interface The Broadband routers firewall can block common hacker 2.7 Firewallattacks and can log the attack activities If you want to restrict users from accessing certain Internet applications/services e.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services Page Add PC Page Example Access Control 2.7.2 URL Blocking 2.7.3 DoS Denial of Service Intrusion Detection FeatureParameters DescriptionEnable DMZ Enable/disable DMZ2.7.4 DMZ ParametersView the Broadband router’s current setting status View any attempts that have been made to illegally gain accessChapter View the Broadband router’s system log3.1 Status and Information 3.2 Internet Connection the Primary DNS and Secondary DNS being used3.3 Device Status View the operation log of the system This page shows the current system log of the Broadband router3.5 Security Log updated situation 3.6 Active DHCP ClientThis page shows all DHCP clients LAN PCs currently connected to your network. The “Active DHCP Client Table”Statistics LAN and Wireless LAN3.7 Statistics Shows the counters of packets sent and received on WANYou can reset the router’s system should any problem exist Chapter4.1 Configuration Tools This page allows you to upgrade the router’s firmware 4.3 Reset How to Manually find your PC’s IP and MAC address Appendix AGlossary Application ProtocolPort Number Telnet