Manuals / Topcom / Computer Equipment / Network Router

Topcom WBR 7101GMR manual 2.4.3.2 802.1x only

Models: WBR 7101GMR

1 98

Download 98 pages 44.71 Kb

Page 51

Manual background

2.4.3.2 802.1x only

IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. This mode only authenticates user by IEEE 802.1x, but it does not encryption the data during communication.

Parameters	Default	Description

RADIUS Server IP address		The IP address of external RADIUS server.
RADIUS Server Port		The service port of the external RADIUS server.
RADIUS Server Password		The password used by external RADIUS server.

Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)

51

Image 51

Topcom WBR 7101GMR manual 2.4.3.2 802.1x only

Contents

Full User Guide Skyr@cer WBR 7101gmrGetting started Package ContentFeatures Front PanelReset Introduction 2 Wide Area Network WAN 3 ResetGet to know the Broadband Router Back Panel 1 Local Area Network LANFront Panel Figure 1.2 below shows a typical setup for a Local Area Network LAN Setup Diagram2a Windows 95/98/Me Configure your PC to obtain an IP address automaticallyx DNS Configuration Select Disable DNS x WINS Configuration Select Disable WINS Resolution2b Windows XP 3 In the Local Area Connection window, click the Properties button 2c Windows2d Windows NT x IP Address Select Obtain an IP address from a DHCP server Quick Setup Wizard Chapter Tools Chapter General Setup ChapterAddress Mapping, Virtual Server, Access Status Information ChapterLogout Tools ChapterChapter Set Time ZoneStart Daylight Savings Time Click on NEXT to proceed to the next page step 2 Broadband Type If your ISP requires a Host Name, type in the host name This is the IP address that your ISP has given you 1.3 PPPoE interface. The WAN connection will not disconnected due when you click “Connect” manually from the Web userto the idle timeout. If the WAN line breaks down and latter If you select “Manual”, the router will connect to ISP only1.4 PPTP Password 1.5 L2TP THE ROUTER WHEN YOU FINISHED USING THE INTERNET Page Description Password1.6 Telstra Big Pond ParameterThis section allows you to set the Broadband router’s system ChapterWireless Description 2.1 SystemDescription 2.1.2 Password Settings2.1.1 Time Zone ParameterParameters Confirmed PasswordCurrent Password New Passwordmanagement/configuration access to the Broadband router from a ParametersDescription Host AddressSelect “Enabled” to enable the remote management function Enabled2.2 WAN DescriptionYour ISP has given you an IP address already Choose the Dynamic IP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name, Domain Name and MAC address see chapter 1 “Cable Modem” for more detail Domain Name Server DNS Server 2.2.7 DNSParameters Description2.2.8 DDNS DefaultEnable/Disable Password/Key192.168.1.1 192.168.1.100 to End IP 192.168.1.199. If you Lease TimeIP Address Pool Domain Name2.4 Wireless AP Mode setting Page AP Bridge-Point to Point mode setting page AP Bridge-Point to Multi-Point mode setting page AP Bridge-WDS mode setting page Set Security to be transmitted. If you set this value too low, it 2.4.2 Advanced SettingsFragment Threshold specifies the maximum size of packet during the fragmentation of dataCTS Protection Data RatePreamble Type Broadcast ESSIDYou can select the WEP key length for ASCII Characters guest Default KeyOnly the key you select it in the Default key will transmitted in the wireless network. Fill the text2.4.3.2 802.1x only IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. This mode also uses WEP to encrypt the data during communication 2.4.3.4 WPA Pre-shared key Fill the text box by following the rules below The Pre-shared key is used to authenticate andencrypt data transmitted in the wireless network Pre-shared Key2.4.3.5 WPA Radius 2.5 QoS 2.4.4 Access ControlEnable/Disable QoS Add a QoS rule into the table Edit QoS Rule Remote IP Address ResetLocal IP Address Local Port Range2.6 NAT 2.6.6 Static Routing 2.6.5 ALG SettingPrivate IP Delete All button. Click Reset will clear your settings from the Current Port ForwardingTable, select the Port Forwarding settings you Forwarding settings from the table, just clickThis is the LAN client/host IP address that the Public Port Public Port Example Virtual Server Enable Trigger Port Example Example Special ApplicationsPage Parameters 2.6.4 UPnP SettingsDefault UPnP Feature2.6.5 ALG Settings 2.6.6 Static Routing Interface 2.7 Firewall The Broadband routers firewall can block common hackerattacks and can log the attack activities If you want to restrict users from accessing certain Internet applications/services e.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services Page Add PC Page Example Access Control 2.7.2 URL Blocking Description 2.7.3 DoS Denial of ServiceIntrusion Detection Feature ParametersParameters Enable DMZEnable/disable DMZ 2.7.4 DMZView the Broadband router’s system log View the Broadband router’s current setting statusView any attempts that have been made to illegally gain access Chapter3.1 Status and Information the Primary DNS and Secondary DNS being used 3.2 Internet Connection3.3 Device Status This page shows the current system log of the Broadband router View the operation log of the system3.5 Security Log connected to your network. The “Active DHCP Client Table” updated situation3.6 Active DHCP Client This page shows all DHCP clients LAN PCs currentlyShows the counters of packets sent and received on WAN StatisticsLAN and Wireless LAN 3.7 StatisticsChapter You can reset the router’s system should any problem exist4.1 Configuration Tools This page allows you to upgrade the router’s firmware 4.3 Reset Appendix A How to Manually find your PC’s IP and MAC addressGlossary Telnet ApplicationProtocol Port Number