AC I/P-V Freq .0Hz, BYP I/P-V Freq .0Hz, 32TIM | Toshiba G8000

MEASUREMENT SCREENS

O/P CURRENT (PEAK)

TABLE 13.2 - CONTINUED

Shows the peak output current peak (%) for each phase.

U50[%]

V50[%]

W50[%]

Peak value of output current

RMS value for rated current x 1.41

x 100 [%]

AC INPUT

AC I/P-V 480[V]

FREQ. 60.0[Hz]

BYPASS INPUT

BYP I/P-V 480[V]

FREQ. 60.0[Hz]

Shows the AC Input Voltage (line-to-line) and frequency.

Shows the Bypass Input Voltage (line-to-line voltage) and frequency.

BATTERY

BACK-UP RATING 10[MIN]

DISCHARGING 15[MIN]

Shows the remaining battery backup time with rated load and cumulative discharged time.

DC INPUT

DC-V 632[V]

BATT-V 400[V]

BATT- I 0[A]

MODE COUNT

UPS 35[H] BATTERY 56[MIN]

32[TIM]

CLOCK

TIME 03-24-06 13:58

Shows the internal DC bus voltage, battery voltage and battery current.

The battery current value displayed is negative during recharge and positive during discharge.

Shows the cumulative UPS operation time, the cumulative battery backup time and the number of battery backup operations.

The current time is displayed if there are no faults recorded, or after the reset button is pressed.

Date is displayed in the mm-ddyyy format. The unit does not calculate daylight savings time.

Time is displayed in the 24-hour format (e.g. 1:58 P.M. = 1358 Hrs.)

G8000 Series Installation and Operation Manual

51

Image 59

Toshiba G8000 operation manual AC I/P-V Freq .0Hz, BYP I/P-V Freq .0Hz, DC-V BATT-V BATT- I 0A, 32TIM, Time 03-24-06

Contents

G8000 Series Page Document November Qualified Personnel only Uninterruptible Power System UPS Toshiba International Corporation PurposeToshiba’s Customer Support Center Toshiba Customer Support Center Table of Contents 11.3 Introduction Prohibited Symbol indicates do not take action General Safety InstructionsSymbols Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Do not tilt the UPS more than 10 from upright position General MaintenanceKeep the area arround the UPS clean Transporting/Unpacking Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Keep the Specified Clearance around the UPS Installation PrecautionsInstall the UPS in a controlled environment Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation PrecautionsPage Follow the torque criteria for tightening screws Wiring/ConnectionPerform wiring and connections with correct polarity Connect only one 1 ground wire to the earth ground terminal For 100, 150, 225KVA GND 150/225 kVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 300 kVA UPS Exterior Dimensions Inches Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Qualified Personnel shall Maintenance PrecautionsQualified Personnel only Do not open or mutilate the batteries DisposalDo not dispose of the batteries in a fire Installation UPS Clearance Unpacking Anchor Bolts Anchor Bolt Installation Detail External Wiring Diagram UPS Wiring Block Number Cable Size Tightening Torque Terminal Blocks and Power Cables Recommended Cable Size & Tightening Torque for 150 kVA UPS AC Input Bypass AC Output Battery Control Wires CRA-1/OL Plate #4 Terminal Bus # Recommendation Bus Number Cable Size Tightening Torque Be sure to ground the UPS as specified Grounding WireExternal Breakers G8000 100 kVA G8000 150/225 kVA Signal Name Operation Control Wires 10 Connection Between UPS, Battery Cabinet & Bypass Breaker 11 Grounding Configuration with Input Neutral Grounded Grounding Configuration Recommended Configuration for delta-input Grounding Configuration without input neutral 15 Grounding Configuration with CORNER-GROUNDED DELTA-INPUT Grounding Configuration with corner-grounded delta-input Terms Specification Remarks UPS SpecificationsGeneral Specification Mechanical Specification Rated Capacity 150 kVA 225 kVA 300 kVA Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic display Panel LCD/LED INDICAtors 13.2 LCD/LED Indicators Name Description LCD Indicators 50% Normal DisplayAC-VO AC- I O 50% Volt Freq .0Hz 32TIM AC I/P-V Freq .0HzBYP I/P-V Freq .0Hz DC-V BATT-V BATT- I 0A 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS Epo and Control Power supply operating switches Perform the pre-operational check before operating the UPS Operation TypesPre-operational Check Procedure to start the UPS is shown in Steps Startup Procedures AC Vo 480 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Equal Charge LED is on Types of Errors TroubleshootingEmergency Power Off EPO 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays Over Heat Fault Messages LCD Message Indication Description Button functions LCD Scroll w/ faults or warnings Do not open the front and/or rear panels Contact Toshiba in the event of malfunction or faultRestoring UPS Operation Do not attempt to modify or relocate the UPSPage Page Industrial Division