Startup Procedures | Toshiba G8000 guide

14.3 Startup Procedures

The procedure to start the UPS is shown in Steps 1-5.	LED Key
								- LED Off
								- LED On
								- LED Flash

STEP 1

Turn on the control power supply switch. (Figure 14.1) and ensure the operation lock is set to OPERATION. (Figure 13.1 - 1)

AC INPUT

BATTERIES

BYPASS INPUT

SYSTEM INITIALIZE

	UPS
CONVERTER	INVERTER
FLOAT CHARGE	AC
EQUAL CHARGE	AC
DISCHARGE	SWITCH

BYPASS

AC OUTPUT

STEP 2

Wait for a few seconds.

AC INPUT

BATTERIES

BYPASS INPUT

BYPASS

PRESS ‘RUN’ SWITCH

	UPS
CONVERTER	INVERTER
FLOAT CHARGE	AC
EQUAL CHARGE	AC
DISCHARGE	SWITCH

BYPASS

AC OUTPUT

STEP 3

Press the “RUN” button for at least 0.5 seconds.

CONVERTER LED is “ON” and INVERTER LED flashes.

AC INPUT

BATTERIES

BYPASS INPUT

BYPASS

UPS STARTING

WAIT FOR A WHILE

	UPS
CONVERTER	INVERTER
FLOAT CHARGE	AC
EQUAL CHARGE	AC
DISCHARGE	SWITCH	AC OUTPUT
DISCHARGE		AC OUTPUT

BYPASS

56	G8000 Series Installation and Operation Manual

Image 64

Toshiba G8000 operation manual Startup Procedures, Procedure to start the UPS is shown in Steps

Contents

G8000 Series Page Document November Qualified Personnel only Uninterruptible Power System UPS Purpose Toshiba’s Customer Support CenterToshiba Customer Support Center Toshiba International Corporation Table of Contents 11.3 Introduction Symbols General Safety InstructionsProhibited Symbol indicates do not take action Signal Words Qualified Personnel Important Safety Instructions Factory Authorized Personnel Safety Precautions Disclaimer General Maintenance Keep the area arround the UPS cleanTransporting/Unpacking Do not tilt the UPS more than 10 from upright position Do not transport, move, store, or place the UPS on its side Avoid vibration or shock exceeding 0.5G Inspection/Storage Install the UPS in a controlled environment Installation PrecautionsKeep the Specified Clearance around the UPS Do not install the UPS where water may fall on it Do not block air vents Installation Precautions Environment standardPage Wiring/Connection Perform wiring and connections with correct polarityConnect only one 1 ground wire to the earth ground terminal Follow the torque criteria for tightening screws For 100, 150, 225KVA GND 150/225 kVA UPS Warning Labels Weight and Dimensions Model Unit Shipping 300 kVA UPS Exterior Dimensions Inches Transporting Transporting By Crane 8.5 show examples of acceptable and unacceptable operations Transporting By Forklift Transporting UPS by Forklift Operating Precautions Storage/Operating EnvironmentPage Qualified Personnel only Maintenance PrecautionsQualified Personnel shall Do not dispose of the batteries in a fire DisposalDo not open or mutilate the batteries Installation Unpacking UPS Clearance Anchor Bolt Installation Detail Anchor Bolts UPS Wiring External Wiring Diagram Terminal Blocks and Power Cables Block Number Cable Size Tightening Torque Recommended Cable Size & Tightening Torque for 150 kVA UPS AC Input Bypass AC Output Battery Control Wires CRA-1/OL Plate #4 Bus Number Cable Size Tightening Torque Terminal Bus # Recommendation External Breakers Grounding WireBe sure to ground the UPS as specified G8000 100 kVA G8000 150/225 kVA Control Wires Signal Name Operation 10 Connection Between UPS, Battery Cabinet & Bypass Breaker Grounding Configuration 11 Grounding Configuration with Input Neutral Grounded Grounding Configuration without input neutral Recommended Configuration for delta-input Grounding Configuration with corner-grounded delta-input 15 Grounding Configuration with CORNER-GROUNDED DELTA-INPUT UPS Specifications General SpecificationMechanical Specification Terms Specification Remarks Rated Capacity 150 kVA 225 kVA 300 kVA Electrical Specification Do not open the front cover Operator Interface UPS may not respond if the button press is too short Key-Switch and Buttons Graphic display Panel KEY-SWITCH/OPERATING Buttons 13.2 LCD/LED Indicators Graphic display Panel LCD/LED INDICAtors LCD Indicators Name Description Normal Display AC-VO AC- I O 50%Volt Freq .0Hz 50% AC I/P-V Freq .0Hz BYP I/P-V Freq .0HzDC-V BATT-V BATT- I 0A 32TIM Fault Display 09-09-06 LCD Scroll Abbreveations Epo and Control Power supply operating switches Operating the UPS Pre-operational Check Operation TypesPerform the pre-operational check before operating the UPS Startup Procedures Procedure to start the UPS is shown in Steps AC Vo 480 AC Io 50% Switch Power Supply UPS→Bypass Bypass LED is on Stop Complete Shutdown DC-V 0 BATT-V 0 BATT-I 0 a Changing Between Float Charge and Equalize Charge Make sure that the Float Charge LED is on Make sure that the Equal Charge LED is on Emergency Power Off EPO TroubleshootingTypes of Errors Faults and Warnings Data Screen 09-09-06 LCD Fault & Warning Displays Fault Display Fault Messages Over Heat LCD Message Indication Description LCD Scroll w/ faults or warnings Button functions Contact Toshiba in the event of malfunction or fault Restoring UPS OperationDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsPage Page Industrial Division