43 Advanced Security settings | TP-Link TL-WA5110G manual

Figure 4-43 Advanced Security settings

Figure 4-43 Advanced Security settings

¾Packets Statistic interval (5 ~ 60) - The default value is 10. Select a value between 5 and 60 seconds from the pull-down list. The Packets Statistic interval value indicates the time section of the packets statistic. The result of the statistic used for analysis by SYN Flood, UDP Flood and ICMP-Flood.

¾DoS protection - Enable or Disable the DoS protection function. Only when it is enabled, will the flood filters be effective.

¾Enable ICMP-FLOOD Attack Filtering - Enable or Disable the ICMP-FLOOD Attack Filtering.

¾ICMP-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value between 5 ~ 3600 packets. When the current ICMP-FLOOD Packets number is beyond the set value, the router will start up the blocking function immediately.

¾Enable UDP-FLOOD Filtering - Enable or Disable the UDP-FLOOD Filtering.

¾UDP-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value between 5 ~ 3600 packets. When the current UPD-FLOOD Packets numbers is beyond the set value, the router will start up the blocking function immediately.

¾Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN- FLOOD Attack Filtering.

¾TCP-SYN-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value between 5 ~ 3600 packets. When the current TCP-SYN-FLOOD Packets numbers is beyond the set value, the router will start up the blocking function immediately.

¾Ignore Ping Packet from WAN Port - Enable or Disable ignore ping packet from WAN port. The default is disabled. If enabled, the ping packet from the Internet cannot access the router.

¾Forbid Ping Packet from LAN Port - Enable or Disable forbidding Ping Packet to access

47

Image 55

TP-Link TL-WA5110G manual 43 Advanced Security settings

Contents

1910010154 TL-WA5110G 54M High Power Wireless Access Point All rights reserved COPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning Country General authorization required for outdoor useand public service National Restrictions 2400.0-2483.5 MHz EN623112008 Product Description 54 M High Power Wireless Access PointETSI EN 300 328 V1.7.1 ETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006 CONTENTS Configuring the Device in AP Operation Mode 5.6.1 Package Contents Chapter 1. Product Overview 1.2 Features1.1 Overview of the Product 1.3 Conventions Indication Chapter 2. Hardware Installation2.1. The Front Panel 2.2. The Rear Panel 2.4. Environment Requirements 2.5. Connecting the DeviceEnsure the AP is powered on before it restarts completely 2.3. System Requirements 3. Connect the AP to the desktop PC 3.1. Configure the Device Chapter 3. Quick Installation GuideFor Windows 98 OS or earlier, the PC and AP may need to be restarted Please check the connection following these steps 3.2. Quick Setup Figure 3-4 Login Windows Figure 3-7 Choose WAN Connection Type Figure 3-9 Quick Setup - Static IP The IP parameters should have been provided by your ISP Figure 3-11 Quick Setup - Wireless settings 4.2 Status 4.1 Login 4. Traffic Statistics IP address and Subnet Mask 2. WirelessSSID, Channel, Mode, Wireless MAC address, and IP address 3. WAN 1. LAN 4.5.1 LAN 4.3 Quick Setup4.4 Operation Mode 4.5 Network 4.5.2 WAN Figure 4-5 WAN - Dynamic IP You should type the following parameters into the spaces provided Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE 4.5.3 MAC Clone 2 If you click Save, the router will prompt you to reboot 4.6 Wireless4.6.1 Basic Settings 1 Only the PC on your LAN can use the Clone MAC Address To feature The device will reboot automatically after you click the Save button 4.6.2 Wireless Mode Figure 4-12 Wireless Mode Figure 4-13 AP List Figure 4-14 Wireless Mode settings in AP Router mode 4.6.3 Security SettingsYou can select one of the following security options ¾ WEP - Select 802.11 WEP security Figure 4-15 Wireless Security2. Shared Key - Select 802.11 Shared Key authentication 3. Open System - Select 802.11 Open System authentication 4.6.4 MAC Filtering To set up an entry, follow these instructions Figure 4-16 Wireless MAC address Filtering¾ Status - The status of this entry either Enabled or Disabled ¾ Description - A simple description of the wireless station 6. Click the Save button to save this entry 4.6.6 Distance Setting 4.6.5 Wireless StatisticsThis page will be refreshed automatically every 5 seconds 4.6.8 Throughput Monitor 4.6.7 Antenna Alignment 4.7 DHCP 4.7.1 DHCP Settings 4.7.2 DHCP Clients List To Reserve IP addresses 4.7.3 Address Reservation 4.8 Wireless settings 4.9.1 Virtual Servers 4.9 Forwarding To setup a virtual server entry, please take the following steps 4.9.2 Port Triggering 4.9.3 DMZ 4.9.4 UPnP 4.10.1 Firewall 4.10Security 4.10.2 IP Address Filtering 4.10.3 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions Click the Enabled All button to make all entries enabledFigure 4-39 Domain Filtering Figure 4-40 Add or Modify a Domain Filtering entry 4.10.4 MAC Address Filtering 4.10.5 Advanced Security Figure 4-43 Advanced Security settings To add static routing entries 4.11Static Routing 4.12.1 Dyndns.org DDNS 4.12Dynamic DNS 4.12.2 Oray.net DDNS 4.12.3 Comexe.cn DDNS 4.13.1 Time 4.13System Tools 2 The time will be lost if the router is turned off 1. Select Using Daylight Saving Time2 The router will reboot after the Upgrading is finished 4.13.2 Firmware 4.13.4 Backup & Restore 4.13.3 Factory Defaults4.13.5 Ping Watch Dog 4.13.6 Speed Test 4.13.7 Reboot 4.13.9 Syslog 4.13.8 Password 4.13.10 Remote Management ICMP 4.13.11 StatisticsStatistics Table Bytes Click the Refresh button to refresh immediately TCP SYN Tx 5.1 Login Chapter 5. Configuring the Device in AP Operation Mode5.2 Status 5.4 Operation Mode 5.3 Quick Setup5.5 Network 5.6.1 Basic Settings 5.6 Wireless3） The device will reboot automatically after clicking Save 5.6.2 Wireless Mode Page If the available AP can’t support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP Figure 5-8 Point to Point Bridge Page the wireless network with wireless antenna accessories 5.6.3 Security Settings Figure 5-11 Wireless Security 5.6.4 MAC Filtering Figure 5-13 Add or Modify Wireless MAC Address Filtering entry Figure 5-12 Wireless MAC address Filtering 6. Click the Save button to save this entry 5.6.6 Distance Setting 5.6.5 Wireless Statistics 5.6.7 Antenna Alignment 5.7 DHCP 5.6.8 Throughput Monitor 5.7.2 DHCP Clients List 5.7.1 DHCP Settings 5.7.3 Address Reservation 5.8 Wireless settings 5.9.1 Firmware 5.9 System Tools 5.9.3 Backup & Restore 5.9.2 Factory Defaults 5.9.5 Speed Test 5.9.4 Ping Watch Dog2. Wrong process will lead the device unmanaged Figure 5-29 Speed Test 5.9.7 Password 5.9.6 Reboot Click Clear ALL to clear all the logs 5.9.8 SyslogClick Save when finished Click Clear All to clear all Figure 5-32 System Log Appendix A FAQ 3. I want to use Netmeeting, what do I need to do? 4. I want to build a Web Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 1. Configure TCP/IP component Appendix B Configuring the PCs Now you have two ways to configure the TCP/IP protocol below ¾ Setting IP address automatically ¾ Setting IP address manually Click OK to keep your settings Physical and Environment Appendix C SpecificationsWireless General Appendix D Glossary