Click OK to keep your settings | TP-Link TL-WA5110G instruction

Click OK to keep your settings.

Figure 0-4

Now:

Click OK to keep your settings.

93

Image 101

TP-Link TL-WA5110G manual Click OK to keep your settings

Contents

1910010154 TL-WA5110G 54M High Power Wireless Access Point All rights reserved COPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTFCC RF Radiation Exposure Statement and public service General authorization required for outdoor useNational Restrictions 2400.0-2483.5 MHz Country ETSI EN 300 328 V1.7.1 Product Description 54 M High Power Wireless Access PointETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006 EN623112008 CONTENTS Configuring the Device in AP Operation Mode 5.6.1 Package Contents 1.1 Overview of the Product 1.2 FeaturesChapter 1. Product Overview 1.3 Conventions 2.1. The Front Panel Chapter 2. Hardware Installation2.2. The Rear Panel Indication Ensure the AP is powered on before it restarts completely 2.5. Connecting the Device2.3. System Requirements 2.4. Environment Requirements 3. Connect the AP to the desktop PC For Windows 98 OS or earlier, the PC and AP may need to be restarted Chapter 3. Quick Installation Guide3.1. Configure the Device Please check the connection following these steps 3.2. Quick Setup Figure 3-4 Login Windows Figure 3-7 Choose WAN Connection Type Figure 3-9 Quick Setup - Static IP The IP parameters should have been provided by your ISP Figure 3-11 Quick Setup - Wireless settings 4.2 Status 4.1 Login SSID, Channel, Mode, Wireless MAC address, and IP address 3. WAN IP address and Subnet Mask 2. Wireless1. LAN 4. Traffic Statistics 4.4 Operation Mode 4.3 Quick Setup4.5 Network 4.5.1 LAN 4.5.2 WAN Figure 4-5 WAN - Dynamic IP You should type the following parameters into the spaces provided Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE 4.5.3 MAC Clone 4.6.1 Basic Settings 4.6 Wireless1 Only the PC on your LAN can use the Clone MAC Address To feature 2 If you click Save, the router will prompt you to reboot The device will reboot automatically after you click the Save button 4.6.2 Wireless Mode Figure 4-12 Wireless Mode Figure 4-13 AP List You can select one of the following security options 4.6.3 Security SettingsFigure 4-14 Wireless Mode settings in AP Router mode 2. Shared Key - Select 802.11 Shared Key authentication Figure 4-15 Wireless Security3. Open System - Select 802.11 Open System authentication ¾ WEP - Select 802.11 WEP security 4.6.4 MAC Filtering ¾ Status - The status of this entry either Enabled or Disabled Figure 4-16 Wireless MAC address Filtering¾ Description - A simple description of the wireless station To set up an entry, follow these instructions 6. Click the Save button to save this entry This page will be refreshed automatically every 5 seconds 4.6.5 Wireless Statistics4.6.6 Distance Setting 4.6.8 Throughput Monitor 4.6.7 Antenna Alignment 4.7 DHCP 4.7.1 DHCP Settings 4.7.2 DHCP Clients List To Reserve IP addresses 4.7.3 Address Reservation 4.8 Wireless settings 4.9.1 Virtual Servers 4.9 Forwarding To setup a virtual server entry, please take the following steps 4.9.2 Port Triggering 4.9.3 DMZ 4.9.4 UPnP 4.10.1 Firewall 4.10Security 4.10.2 IP Address Filtering 4.10.3 Domain Filtering Figure 4-39 Domain Filtering Click the Enabled All button to make all entries enabledFigure 4-40 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions 4.10.4 MAC Address Filtering 4.10.5 Advanced Security Figure 4-43 Advanced Security settings To add static routing entries 4.11Static Routing 4.12.1 Dyndns.org DDNS 4.12Dynamic DNS 4.12.2 Oray.net DDNS 4.12.3 Comexe.cn DDNS 4.13.1 Time 4.13System Tools 2 The router will reboot after the Upgrading is finished 1. Select Using Daylight Saving Time4.13.2 Firmware 2 The time will be lost if the router is turned off 4.13.5 Ping Watch Dog 4.13.3 Factory Defaults4.13.4 Backup & Restore 4.13.6 Speed Test 4.13.7 Reboot 4.13.9 Syslog 4.13.8 Password 4.13.10 Remote Management Statistics Table 4.13.11 StatisticsBytes ICMP Click the Refresh button to refresh immediately TCP SYN Tx 5.2 Status Chapter 5. Configuring the Device in AP Operation Mode5.1 Login 5.5 Network 5.3 Quick Setup5.4 Operation Mode 3） The device will reboot automatically after clicking Save 5.6 Wireless5.6.1 Basic Settings 5.6.2 Wireless Mode Page If the available AP can’t support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP Figure 5-8 Point to Point Bridge Page the wireless network with wireless antenna accessories 5.6.3 Security Settings Figure 5-11 Wireless Security 5.6.4 MAC Filtering Figure 5-13 Add or Modify Wireless MAC Address Filtering entry Figure 5-12 Wireless MAC address Filtering 6. Click the Save button to save this entry 5.6.6 Distance Setting 5.6.5 Wireless Statistics 5.6.7 Antenna Alignment 5.7 DHCP 5.6.8 Throughput Monitor 5.7.2 DHCP Clients List 5.7.1 DHCP Settings 5.7.3 Address Reservation 5.8 Wireless settings 5.9.1 Firmware 5.9 System Tools 5.9.3 Backup & Restore 5.9.2 Factory Defaults 2. Wrong process will lead the device unmanaged 5.9.4 Ping Watch Dog5.9.5 Speed Test Figure 5-29 Speed Test 5.9.7 Password 5.9.6 Reboot Click Save when finished Click Clear All to clear all 5.9.8 SyslogFigure 5-32 System Log Click Clear ALL to clear all the logs Appendix A FAQ 3. I want to use Netmeeting, what do I need to do? 4. I want to build a Web Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 1. Configure TCP/IP component Appendix B Configuring the PCs Now you have two ways to configure the TCP/IP protocol below ¾ Setting IP address automatically ¾ Setting IP address manually Click OK to keep your settings Wireless Appendix C SpecificationsGeneral Physical and Environment Appendix D Glossary