Manuals / TP-Link / Computer Equipment / Network Card

TP-Link TL-WA5110G manual Ping Watch Dog, Speed Test, Wrong process will lead the device unmanaged

Models: TL-WA5110G

1 104

Download 104 pages 34.47 Kb

Page 90

2.Wrong process will lead the device unmanaged.

To restore the AP's configuration, please take the following steps:

•Click Browse to find the location of configuration file which you want to restore.

•Click Restore to update the configuration with the file whose path is the one you have input or selected in the blank.

)Note:

1.The current configuration will be covered by the uploading configuration file.

2.Wrong process will lead the device unmanaged.

3.The restoring process will last for 20 seconds and the AP will restart automatically. Do not power off the device during the process to avoid any damage.

5.9.4 Ping Watch Dog

The Ping Watch Dog is dedicated for continuous monitoring of the particular connection to remote host using the Ping tool. It makes this device continuously ping a user defined IP address (it can be the internet gateway for example). If it is unable to ping under the user defined constraints, this device will automatically reboot.

Figure 5-28 Ping Watch Dog Utility

¾Enable: Turn on/off Ping Watch Dog.

¾IP Address: The IP address of the target host where the Ping Watch Dog Utility is sending ping packets.

¾Interval: Time internal between two ping packets which are sent out continuously.

¾Delay: Time delay before first ping packet is sent out when the device is restarted.

¾Fail Count: Upper limit of the ping packet the device can drop continuously. If this value is overrun, the device will restart automatically.

Be sure to click the Submit button to make your settings in operation.

5.9.5 Speed Test

The Speed Test is dedicated for testing the connection speed to and from any reachable IP address on current network, especially when we are building wireless network between devices which are far away from each other. It should be used for the preliminary throughput estimation between two network devices. The estimation is rough. You can input the remote device's

82

Image 90

TP-Link TL-WA5110G manual Ping Watch Dog, Speed Test, Wrong process will lead the device unmanaged

Contents

TL-WA5110G 54M High Power Wireless Access Point 1910010154COPYRIGHT & TRADEMARKS All rights reservedFCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning National Restrictions 2400.0-2483.5 MHz General authorization required for outdoor useand public service CountryETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006 Product Description 54 M High Power Wireless Access PointETSI EN 300 328 V1.7.1 EN623112008CONTENTS Configuring the Device in AP Operation Mode Chapter5.6.1 Package Contents 1.2 Features Chapter 1. Product Overview1.1 Overview of the Product 1.3 Conventions 2.2. The Rear Panel Chapter 2. Hardware Installation2.1. The Front Panel Indication2.3. System Requirements 2.5. Connecting the DeviceEnsure the AP is powered on before it restarts completely 2.4. Environment Requirements3. Connect the AP to the desktop PC Chapter 3. Quick Installation Guide 3.1. Configure the DeviceFor Windows 98 OS or earlier, the PC and AP may need to be restarted 3.2. Quick Setup Please check the connection following these stepsFigure 3-4 Login Windows Figure 3-7 Choose WAN Connection Type The IP parameters should have been provided by your ISP Figure 3-9 Quick Setup - Static IPFigure 3-11 Quick Setup - Wireless settings 4.1 Login 4.2 Status1. LAN IP address and Subnet Mask 2. WirelessSSID, Channel, Mode, Wireless MAC address, and IP address 3. WAN 4. Traffic Statistics4.5 Network 4.3 Quick Setup4.4 Operation Mode 4.5.1 LAN4.5.2 WAN Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP You should type the following parameters into the spaces providedFigure 4-7 WAN - PPPoE 4.5.3 MAC Clone 1 Only the PC on your LAN can use the Clone MAC Address To feature 4.6 Wireless4.6.1 Basic Settings 2 If you click Save, the router will prompt you to reboot4.6.2 Wireless Mode The device will reboot automatically after you click the Save buttonFigure 4-12 Wireless Mode Figure 4-13 AP List 4.6.3 Security Settings Figure 4-14 Wireless Mode settings in AP Router modeYou can select one of the following security options 3. Open System - Select 802.11 Open System authentication Figure 4-15 Wireless Security2. Shared Key - Select 802.11 Shared Key authentication ¾ WEP - Select 802.11 WEP security4.6.4 MAC Filtering The device will reboot automatically after you click the Save button¾ Description - A simple description of the wireless station Figure 4-16 Wireless MAC address Filtering¾ Status - The status of this entry either Enabled or Disabled To set up an entry, follow these instructions6. Click the Save button to save this entry 4.6.5 Wireless Statistics 4.6.6 Distance SettingThis page will be refreshed automatically every 5 seconds 4.6.7 Antenna Alignment 4.6.8 Throughput Monitor4.7.1 DHCP Settings 4.7 DHCP4.7.2 DHCP Clients List 4.7.3 Address Reservation To Reserve IP addresses4.8 Wireless settings 4.9 Forwarding 4.9.1 Virtual ServersTo setup a virtual server entry, please take the following steps 4.9.2 Port Triggering 4.9.3 DMZ 4.9.4 UPnP 4.10Security 4.10.1 Firewall4.10.2 IP Address Filtering 4.10.3 Domain Filtering Figure 4-39 Domain Filtering Click the Enabled All button to make all entries enabledClick the Disabled All button to make all entries disabled Figure 4-40 Add or Modify a Domain Filtering entry4.10.4 MAC Address Filtering 4.10.5 Advanced Security Figure 4-43 Advanced Security settings 4.11Static Routing To add static routing entries4.12Dynamic DNS 4.12.1 Dyndns.org DDNS4.12.2 Oray.net DDNS 4.12.3 Comexe.cn DDNS 4.13System Tools 4.13.1 Time4.13.2 Firmware 1. Select Using Daylight Saving Time2 The router will reboot after the Upgrading is finished 2 The time will be lost if the router is turned off4.13.3 Factory Defaults 4.13.4 Backup & Restore4.13.5 Ping Watch Dog 4.13.6 Speed Test 4.13.7 Reboot 4.13.8 Password 4.13.9 Syslog4.13.10 Remote Management Bytes 4.13.11 StatisticsStatistics Table ICMPTCP SYN Tx Click the Refresh button to refresh immediatelyChapter 5. Configuring the Device in AP Operation Mode 5.1 Login5.2 Status 5.3 Quick Setup 5.4 Operation Mode5.5 Network 5.6 Wireless 5.6.1 Basic Settings3） The device will reboot automatically after clicking Save 5.6.2 Wireless Mode The device will reboot automatically after you click the Save buttonPage If the available AP can’t support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP Figure 5-8 Point to Point Bridge Page 5.6.3 Security Settings the wireless network with wireless antenna accessories3. Open System - Select 802.11 Open System authentication Figure 5-11 Wireless Security2. Shared Key - Select 802.11 Shared Key authentication ¾ WEP - Select 802.11 WEP security5.6.4 MAC Filtering The device will reboot automatically after you click the Save button¾ Description - A simple description of the wireless station Figure 5-12 Wireless MAC address Filtering¾ Status - The status of this entry either Enabled or Disabled To set up an entry, follow these instructions6. Click the Save button to save this entry 5.6.5 Wireless Statistics 5.6.6 Distance SettingThis page will be refreshed automatically every 5 seconds 5.6.7 Antenna Alignment 5.6.8 Throughput Monitor 5.7 DHCP5.7.1 DHCP Settings 5.7.2 DHCP Clients List5.7.3 Address Reservation To Reserve IP addresses5.8 Wireless settings 5.9 System Tools 5.9.1 Firmware5.9.2 Factory Defaults 5.9.3 Backup & Restore5.9.4 Ping Watch Dog 5.9.5 Speed Test2. Wrong process will lead the device unmanaged Figure 5-29 Speed Test 5.9.6 Reboot 5.9.7 PasswordFigure 5-32 System Log 5.9.8 SyslogClick Save when finished Click Clear All to clear all Click Clear ALL to clear all the logsAppendix A FAQ 3. I want to use Netmeeting, what do I need to do? 4. I want to build a Web Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router Appendix B Configuring the PCs 1. Configure TCP/IP component¾ Setting IP address automatically Now you have two ways to configure the TCP/IP protocol below¾ Setting IP address manually Click OK to keep your settings General Appendix C SpecificationsWireless Physical and EnvironmentAppendix D Glossary