¾ Setting IP address automatically | TP-Link TL-WA5110G guide

Now you have two ways to configure the TCP/IP protocol below:

Figure 0-2

5)The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.

Now you have two ways to configure the TCP/IP protocol below:

¾Setting IP address automatically

Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as shown in the Figure below:

91

Image 99

TP-Link TL-WA5110G manual ¾ Setting IP address automatically, Now you have two ways to configure the TCP/IP protocol below

Contents

1910010154 TL-WA5110G 54M High Power Wireless Access Point All rights reserved COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning Country General authorization required for outdoor useand public service National Restrictions 2400.0-2483.5 MHz EN623112008 Product Description 54 M High Power Wireless Access PointETSI EN 300 328 V1.7.1 ETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006 CONTENTS Configuring the Device in AP Operation Mode 5.6.1 Package Contents 1.2 Features Chapter 1. Product Overview1.1 Overview of the Product 1.3 Conventions Indication Chapter 2. Hardware Installation2.1. The Front Panel 2.2. The Rear Panel 2.4. Environment Requirements 2.5. Connecting the DeviceEnsure the AP is powered on before it restarts completely 2.3. System Requirements 3. Connect the AP to the desktop PC Chapter 3. Quick Installation Guide 3.1. Configure the DeviceFor Windows 98 OS or earlier, the PC and AP may need to be restarted Please check the connection following these steps 3.2. Quick Setup Figure 3-4 Login Windows Figure 3-7 Choose WAN Connection Type Figure 3-9 Quick Setup - Static IP The IP parameters should have been provided by your ISP Figure 3-11 Quick Setup - Wireless settings 4.2 Status 4.1 Login 4. Traffic Statistics IP address and Subnet Mask 2. WirelessSSID, Channel, Mode, Wireless MAC address, and IP address 3. WAN 1. LAN 4.5.1 LAN 4.3 Quick Setup4.4 Operation Mode 4.5 Network 4.5.2 WAN Figure 4-5 WAN - Dynamic IP You should type the following parameters into the spaces provided Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE 4.5.3 MAC Clone 2 If you click Save, the router will prompt you to reboot 4.6 Wireless4.6.1 Basic Settings 1 Only the PC on your LAN can use the Clone MAC Address To feature The device will reboot automatically after you click the Save button 4.6.2 Wireless Mode Figure 4-12 Wireless Mode Figure 4-13 AP List 4.6.3 Security Settings Figure 4-14 Wireless Mode settings in AP Router modeYou can select one of the following security options ¾ WEP - Select 802.11 WEP security Figure 4-15 Wireless Security2. Shared Key - Select 802.11 Shared Key authentication 3. Open System - Select 802.11 Open System authentication 4.6.4 MAC Filtering To set up an entry, follow these instructions Figure 4-16 Wireless MAC address Filtering¾ Status - The status of this entry either Enabled or Disabled ¾ Description - A simple description of the wireless station 6. Click the Save button to save this entry 4.6.5 Wireless Statistics 4.6.6 Distance SettingThis page will be refreshed automatically every 5 seconds 4.6.8 Throughput Monitor 4.6.7 Antenna Alignment 4.7 DHCP 4.7.1 DHCP Settings 4.7.2 DHCP Clients List To Reserve IP addresses 4.7.3 Address Reservation 4.8 Wireless settings 4.9.1 Virtual Servers 4.9 Forwarding To setup a virtual server entry, please take the following steps 4.9.2 Port Triggering 4.9.3 DMZ 4.9.4 UPnP 4.10.1 Firewall 4.10Security 4.10.2 IP Address Filtering 4.10.3 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions Click the Enabled All button to make all entries enabledFigure 4-39 Domain Filtering Figure 4-40 Add or Modify a Domain Filtering entry 4.10.4 MAC Address Filtering 4.10.5 Advanced Security Figure 4-43 Advanced Security settings To add static routing entries 4.11Static Routing 4.12.1 Dyndns.org DDNS 4.12Dynamic DNS 4.12.2 Oray.net DDNS 4.12.3 Comexe.cn DDNS 4.13.1 Time 4.13System Tools 2 The time will be lost if the router is turned off 1. Select Using Daylight Saving Time2 The router will reboot after the Upgrading is finished 4.13.2 Firmware 4.13.3 Factory Defaults 4.13.4 Backup & Restore4.13.5 Ping Watch Dog 4.13.6 Speed Test 4.13.7 Reboot 4.13.9 Syslog 4.13.8 Password 4.13.10 Remote Management ICMP 4.13.11 StatisticsStatistics Table Bytes Click the Refresh button to refresh immediately TCP SYN Tx Chapter 5. Configuring the Device in AP Operation Mode 5.1 Login5.2 Status 5.3 Quick Setup 5.4 Operation Mode5.5 Network 5.6 Wireless 5.6.1 Basic Settings3） The device will reboot automatically after clicking Save 5.6.2 Wireless Mode Page If the available AP can’t support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP Figure 5-8 Point to Point Bridge Page the wireless network with wireless antenna accessories 5.6.3 Security Settings Figure 5-11 Wireless Security 5.6.4 MAC Filtering Figure 5-13 Add or Modify Wireless MAC Address Filtering entry Figure 5-12 Wireless MAC address Filtering 6. Click the Save button to save this entry 5.6.6 Distance Setting 5.6.5 Wireless Statistics 5.6.7 Antenna Alignment 5.7 DHCP 5.6.8 Throughput Monitor 5.7.2 DHCP Clients List 5.7.1 DHCP Settings 5.7.3 Address Reservation 5.8 Wireless settings 5.9.1 Firmware 5.9 System Tools 5.9.3 Backup & Restore 5.9.2 Factory Defaults 5.9.4 Ping Watch Dog 5.9.5 Speed Test2. Wrong process will lead the device unmanaged Figure 5-29 Speed Test 5.9.7 Password 5.9.6 Reboot Click Clear ALL to clear all the logs 5.9.8 SyslogClick Save when finished Click Clear All to clear all Figure 5-32 System Log Appendix A FAQ 3. I want to use Netmeeting, what do I need to do? 4. I want to build a Web Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 1. Configure TCP/IP component Appendix B Configuring the PCs Now you have two ways to configure the TCP/IP protocol below ¾ Setting IP address automatically ¾ Setting IP address manually Click OK to keep your settings Physical and Environment Appendix C SpecificationsWireless General Appendix D Glossary