Wireless Advanced | TP-Link TL-WA730RE manual

150Mbps Wireless N Range Extender User Guide

TL-WA730RE

150Mbps Wireless N Range Extender User Guide

)Note:

If you enable the function and select the “Allow the stations specified by any enabled entries in the list to access” for Filtering Rules, and there are not any enabled entries in the list, thus, no wireless stations can access the device.

4.7.4 Wireless Advanced

Selecting Wireless > Wireless Advanced will allow you to do some advanced settings for the device in the following screen shown in Figure 4-17.As the configuration for each operation mode is almost the same, we take Access Point mode for example here.

Figure 4-17 Wireless Advanced

¾Beacon Interval - Specifies a value between 20-1000 milliseconds. The beacons are the packets sent by the device to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100.

¾RTS Threshold - Specifies the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the device will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346.

¾Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance since excessive packets. 2346 is the default setting and is recommended.

¾DTIM Interval - Determines the interval of the Delivery Traffic Indication Message (DTIM). You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval.

¾Enable WMM - WMM function can guarantee the packets with high- priority messages being transmitted preferentially. It is strongly recommended enabled.

¾Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time.

¾Enable AP Isolation - Isolates all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled.

32

Image 40

TP-Link TL-WA730RE manual Wireless Advanced, 150Mbps Wireless N Range Extender User Guide

Contents

TL-WA730RE 150Mbps Wireless N Range Extender Rev 2.0.0 COPYRIGHT & TRADEMARKS All rights reserved FCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning Safety Information Canadian Compliance StatementIndustry Canada Statement Korea Warning Statements This product can be used in the following countries DECLARATION OF CONFORMITY Product Description 150Mbps Wireless N Range ExtenderThe product carries the CE Mark ETSI EN 300 328 V1.7.1 CONTENTS Package ContentsHardware Installation Chapter 3 Quick Installation Guide Appendix B Factory Defaults Appendix C TroubleshootingAppendix D Specifications Appendix A Application Example Package Contents TL-WA730RE Chapter 1 Introduction 1.1 Product Overview1.2 Conventions TL-WA730RE 150Mbps Wireless N Range Extender User Guide 1.3 Main Features Features1.4 Appearance Benefits 1.4.2 The Rear Panel Ensure the Range Extender is powered on before it restarts completely Chapter 2 Hardware Installation 2.3 Connecting the Device2.1 Before You Begin 2.2 Basic Requirements 1. Connect the Cable or DSL modem to a Router Chapter 3 Quick Installation Guide 3.1 Quick Setup Figure 3-2 Login Windows Figure 3-4 Operation Mode Figure 3-6 AP List Figure 3-7 Wireless Settings - Access Point mode Figure 3-9 Quick Setup - Finish Figure 3-11 Quick Setup - Finish Chapter 4 Configure the Device 4.1 Login 4.2 Status 4.4 Operation Mode 4.3 Quick Setup4.5 WPS I. By PBC To add a new deviceMethod One TL-WA730RE 150Mbps Wireless N Range Extender User Guide TL-WA730RE 150Mbps Wireless N Range Extender User Guide TL-WA730RE 150Mbps Wireless N Range Extender User Guide 4.7 Wireless 4.6 Network 4.7.1 Wireless Settings ¾ Region - Please select the right region from the drop-down list 4.7.2 Wireless Security 1 Repeater Range Extender 3 WPA2-Personal - WPA version WEP Key Format - You can select ASCII or Hexadecimal format. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits 0-9, a-f, A-F in the specified length 2 Access Point 4.7.3 Wireless MAC Filtering To set up an entry, follow these instructions To add a MAC Address Filtering entry, follow these instructions To modify or delete an existing entry 4.7.4 Wireless Advanced 150Mbps Wireless N Range Extender User Guide 4.7.5 Antenna Alignment 4.7.6 Throughput Monitor 4.7.7 Wireless Statistics 4.8 DHCP 4.8.1 DHCP Settings 4.8.2 DHCP Clients List 4.8.3 Address Reservation 4.9 System Tools To Reserve IP addressesTo modify A Reserved IP address To delete all Reserved IP addresses 1. Click Clear All 4.9.1 SNMP 4.9.2 Time Settings ¾ To set time manually 4.9.3 Diagnostic¾ For automatic time synchronization Figure 4-28 Diagnostic 4.9.4 Ping Watch Dog 4.9.5 Firmware Upgrade 4.9.7 Backup & Restore 4.9.6 Factory DefaultsTo upgrade the devices firmware, follow these instructions 4.9.8 Reboot To restore the devices configuration, follow these instructions 4.9.9 Password 4.9.10 System Log Figure 4-36 System Log 4.9.11 Statistics ¾ Statistics Table ¾ Total¾ Current ¾ Modify Appendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless N Range Extender User Guide Appendix B Factory Defaults Default ValueCommon Default Settings Wireless Appendix C Troubleshooting T2. What can I do if I forget my password? 2 Click Change adapter settings 3 Right-click Local Area Connection, and Click Properties 4 Double-click Internet Protocol Version 4 TCP/IPv4 TL-WA730RE 150Mbps Wireless N Range Extender User Guide General Appendix D SpecificationsPhysical and Environment Appendix E Glossary TL-WA730RE 150Mbps Wireless N Range Extender User Guide