Basic Configuration via CLI
!Important! When changing settings, it is usually necessary to type the save ss command in order to update the radio’s flash memory. If you do not type the save ss command, the setting will be lost the next time the radio is rebooted or power cycled.
| SU SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS |
| ||
SU Parameter |
| Description | Related CLI Command |
|
Device ID |
| MAC Address of the SU | N/A |
|
Base ID |
| Specifies the cell or cluster to | set baseid <baseid> |
|
|
| which the SU belongs. | Example: |
|
|
|
|
| |
|
|
| #>Set baseid aa12 |
|
|
|
|
|
|
Target AP |
| If unique AP ID selected, the | targetap <apid> | |
|
| SU can only associate with |
|
|
|
| the specified AP. If ALL is |
|
|
|
| selected, the SU can | Examples: |
|
|
| associate with any AP with a | #>targetap 33 |
|
|
| matching BASE ID. | #>targetap all |
|
Opmode |
| Current Opmode of radio. | opmode on y - set Opmode to “ON.” (note: “y” |
|
|
|
| is necessary if default Opmode is “OFF.”) |
|
|
|
| opmode off – set Opmode to “OFF.” |
|
|
|
|
|
|
Default Opmode |
| Determines the Opmode | set defaultopmode <on or off> | |
|
| (“ON” or “OFF”) of the radio |
|
|
|
| after reboot/power cycle. | Example: |
|
|
| When this parameter is set to | #>set defaultopmode on |
|
|
| “ON,” the radio will progress |
|
|
|
| into Opmode “ON” |
|
|
|
| automatically after |
|
|
|
| reboot/power cycle. |
|
|
IP |
| IP, Subnet, and Gateway | ipconfig [<new ip> <new subnet mask> <new |
|
Subnet |
| address of radio. | gateway>] |
|
Gateway |
|
| Example: |
|
|
|
|
| |
|
|
| #>ipconfig 10.1.1.3 255.0.0.0 10.1.1.1 |
|
|
|
|
|
|
TFTPD |
| TFTPD status (on or off). | tftpd [<onoff>] | |
|
| TFTPD should be turned on | Example: |
|
|
| to import a file into the radio | #>tftpd on |
|
|
| (such as new firmware). |
|
|
|
| Default is off. TFTPD will |
|
|
|
| revert to off after |
|
|
|
| reboot/power cycle. |
|
|
RF TX Power |
| Current transmit power of the | Informational Parameter – can not be manually |
|
|
| SU not including antenna | changed by user. |
|
|
| gain. This is controlled by |
|
|
|
| the AP. |
|
|
Active Channel |
| Shows the channel used in | If Autoscan AP (SW 1) is on, the active channel |
|
|
| the current association, and | (and antenna selection) will be set once the SU |
|
|
| "Associated" or | scans and begins the association process with an |
|
|
| "Disconnected" depending | AP. |
|
|
| on the association status. | If Autoscan AP is off, the active channel is set by |
|
|
|
| the user, using the freq command. |
|
|
|
| freq [<ch#> <vh>] |
|
|
|
| Example: |
|
|
|
|
|
|
Trango Broadband Wireless — User Manual M2400S Rev A | Page 26 | |||
