Manuals / Universal Laser Systems / Computer Equipment / Printer

Universal Laser Systems CLP-100NI-NPRT manual Inking System Assembly, Maintenance

Models: CLP-100NI-NPRT

1 45

Download 45 pages 53.28 Kb

Page 37

INKING SYSTEM ASSEMBLY

MAINTENANCE

INKING SYSTEM ASSEMBLY

The following steps will guide you through the Ink Roll Eccentric Assembly.

1 - Install the O-Ring in the groove of the Eccentric flange, then install one of the white delrin washers on the Eccen- tric.

ECCENTRIC O-RING

FIGURE 74

2 - Apply a thin coating of grease to the O-Ring and the Ec- centric to approximately 1/2” from the flange.

Automotive wheel bearing grease is recommended.

FIGURE 75

3 - Insert the Eccentric into the Inking System Cover. Rotate and pull the Eccentric from the opposite side until the o- ring slips into the bore. When fully seated, the flange of the eccentric will be approximately 0.010” above the sur- face of the cover. Rotate the Eccentric and align the dimple on the Eccentric flange with the dimple in the cover.

4 - Install the second white delrin washer over the Eccentric.

ALIGN DIMPLES

FIGURE 76

FIGURE 77

37

Image 37

Universal Laser Systems CLP-100NI-NPRT manual Inking System Assembly, Maintenance

Contents

OWNER’S MANUAL INSTALLATION - OPERATION - MAINTENANCESTENCILING & MARKING UNIVERSAL STENCILING & MARKING SYSTEMS, INCIMPORTANT NOTE LIMITED WARRANTYPREFACE CODER SPECIFICATIONSQUICK START PAGES 9 THRUCONVEYOR LINE PRINTER SPECIFICATIONS TOP MOUNT SERIES SPECIFICATIONSModel Shown CLP-100NI-NPRT Model Shown CLP-200NI-NPLS CONVEYOR LINE PRINTER SPECIFICATIONS SIDE MOUNT SERIESSPECIFICATIONS INDEXING AND NON-INDEXING MODELS MOUNTING CONFIGURATIONSPECIFICATIONS CODER MODELS DESIGNED FOR METRIC RIBtype PRINTING DIES RIBtype PRINTING DIESSPECIFICATIONS XF NEOPRENE INK ROLLS INK ROLLSTYPE MT INK ROLLS SPECIFICATIONSQUICK START INSTALLING THE INKING SYSTEM ASSEMBLYQUICK START INSTALLING THE PRE-INKED ROLLThe Knurled Drive Wheel Cover is very loose fitting QUICK START8 -Inspect the roll for excess surface wetness. Remove any excess ink by rolling the roll lightly over a piece of absorbent paper QUICK STARTQUICK START The tops of the stainless pins will be flush with the top of theQUICK START INSTALLING THE PRINTING DIESQUICK START ADJUSTING THE INK ROLL ECCENTRICFOR MOUNTING INSTRUCTIONS REFER TO THE APPROPRIATE SECTION FOR YOUR APPLICATION WEB PRINTING - PAGE CARTON PRINTING - PAGEBASIC PRINCIPLES OF OPERATION USING THE 4 OZ. RESERVOIR INK CARTRIDGESNON-POROUS INKING SYSTEM BASIC PRINCIPLES OF OPERATION SELECTING AN APPROPRIATE INKBASIC PRINCIPLES OF OPERATION INK DRYING TIME CONSIDERATIONSTRANSFER ROLLWEB PRINTING WEB PRINTING MOUNTING THE CODER3/8” BOLTS SPECIAL WEB PRINTING APPLICATIONS WEB PRINTINGPRINTING ON NARROW WEB MATERIALS PRINTING DIRECTLY ON MASTER ROLLSWEB PRINTING GANG MOUNTINGCARTON ALIGNMENT CARTON PRINTINGUniversal Non-Porous Conveyor Line Printers are designed so the frame of the machine will pivot on the mount- ing column. This allows the print drum to deflect, or swing, on contact with the leading edge of the carton a maximum of 2. It is recommended that cartons be aligned between guide rails with no more than 1/4 clearance on each side as shown in Figure 40. This should allow ample clearance for cartons and protect your printer from damage CARTON PRINTINGADJUST FOR DIE POSITIONING FOR INDEXING APPLICATIONSCARTON PRINTING 1/4” TO 3/8”CARTON PRINTING Although installing the printing dies in this position restricts how close to the leading edge of the carton you can register the print, it is one of the only ways to ensure a good imprint on every carton. Since the fastest drying non- porous inks will dry in approximately 2 seconds at 75 Degree F. ambient temperature, the ink will also dry on the die face within 2 seconds after it is applied by the transfer roll. If the dies have not contacted the carton surface before then, no imprint will be transferred to the cartonPRE-INKING A NEW INK ROLL MAINTENANCEInk Cartridges CLEANING THE CODER CLEANING THE TRANSFER ROLLDO NOT SUBMERGE THE TRANSFER ROLL IN SOLVENT MAINTENANCEMAINTENANCE CLEANING THE PRINTING DIESPIVOT ARM & INKING SYSTEM ASSEMBLY CONVERSION MOUNTING CONFIGURATION CONVERSION LEFTHAND/RIGHTHAND FIELD CONVERSIONMAINTENANCE MAINTENANCE TENSION ARM ASSEMBLY CONVERSIONMAINTENANCE PRINT DRUM INDEX MECHANISM CONVERSIONCONFIGURATION MAINTENANCEMAINTENANCE REPLACING PRINT DRUM INDEX SPRINGSRIGHT HAND CONFIGURATION LEFT HAND CONFIGURATIONMAINTENANCE REMOVING AND REPLACING INDEX BLOCK “B”2- Lift Index Block “B” straight up to remove MAINTENANCEMAINTENANCE INKING SYSTEM ASSEMBLYMAINTENANCE NON-POROUS CONVEYOR LINE PRINTER CE GUARD ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER CE GUARD ASSEMBLYNON-POROUS CONVEYOR LINE PRINTER ASSEMBLY CF-11 NON-POROUS CONVEYOR LINE PRINTER PARTS LISTNON-POROUS CONVEYOR LINE PRINTER INKING SYSTEM ASSEMBLY OPTIONAL THREADED PLUG WITH O-RING SEAL FOR RESERVOIR PORT NON-POROUS CONVEYOR LINE PRINTER INKING SYSTEM PARTS LISTNON-POROUS CONVEYOR LINE PRINTER PRINT DRUM ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER PRINT DRUM ASSEMBLYNON-POROUS CONVEYOR LINE PRINTER INDEX ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER INDEX ASSEMBLY