Manuals / Universal Laser Systems / Computer Equipment / Printer

Universal Laser Systems CLP-100NI-NPRT Conveyor Line Printer Specifications Side Mount Series

Models: CLP-100NI-NPRT

1 45

Download 45 pages 53.28 Kb

Page 5

Image 5

SPECIFICATIONS

CONVEYOR LINE PRINTER SPECIFICATIONS

SIDE MOUNT SERIES

Model Shown: CLP-200NI-NPLS

5.75

(146.05 MM)

2.49

(63.25 MM)

4.80

(121.92 MM)

2.00

(50.80 MM)

	3	MAX
2		MAX
1
MIN

9.80

(248.92 MM)

11.25

(285.75 MM)

8.25

(209.55 MM)

11.50

(292.10 MM)

NET WEIGHT:	11 LBS. -5 OZS. (5.13 KG.)
MAXIMUM DIE SIZE:	14 RIBS WIDE X 16-15/16" LENGTH (14 RIBS WIDE X 430 MM LENGTH)
MAXIMUM PRINT WIDTH:	1.875" ( 47.6 MM)
PRINT DRUM CIRCUMFERENCE:	APPROXIMATELY 18" (457 MM) MEASURED AT THE DIE FACE

Page 5

Image 5

Universal Laser Systems CLP-100NI-NPRT Conveyor Line Printer Specifications Side Mount Series, Model Shown CLP-200NI-NPLS

Contents

OWNER’S MANUAL INSTALLATION - OPERATION - MAINTENANCESTENCILING & MARKING UNIVERSAL STENCILING & MARKING SYSTEMS, INCIMPORTANT NOTE LIMITED WARRANTYPREFACE CODER SPECIFICATIONSQUICK START PAGES 9 THRUModel Shown CLP-100NI-NPRT SPECIFICATIONSCONVEYOR LINE PRINTER SPECIFICATIONS TOP MOUNT SERIES SPECIFICATIONS CONVEYOR LINE PRINTER SPECIFICATIONS SIDE MOUNT SERIESModel Shown CLP-200NI-NPLS SPECIFICATIONS MOUNTING CONFIGURATIONINDEXING AND NON-INDEXING MODELS SPECIFICATIONS RIBtype PRINTING DIESCODER MODELS DESIGNED FOR METRIC RIBtype PRINTING DIES XF NEOPRENE INK ROLLS INK ROLLSTYPE MT INK ROLLS SPECIFICATIONSQUICK START INSTALLING THE INKING SYSTEM ASSEMBLYQUICK START INSTALLING THE PRE-INKED ROLLThe Knurled Drive Wheel Cover is very loose fitting QUICK START8 -Inspect the roll for excess surface wetness. Remove any excess ink by rolling the roll lightly over a piece of absorbent paper QUICK STARTQUICK START The tops of the stainless pins will be flush with the top of theQUICK START INSTALLING THE PRINTING DIESQUICK START ADJUSTING THE INK ROLL ECCENTRICFOR MOUNTING INSTRUCTIONS REFER TO THE APPROPRIATE SECTION FOR YOUR APPLICATION WEB PRINTING - PAGE CARTON PRINTING - PAGENON-POROUS INKING SYSTEM USING THE 4 OZ. RESERVOIR INK CARTRIDGESBASIC PRINCIPLES OF OPERATION BASIC PRINCIPLES OF OPERATION SELECTING AN APPROPRIATE INKBASIC PRINCIPLES OF OPERATION INK DRYING TIME CONSIDERATIONSTRANSFER ROLLWEB PRINTING 3/8” BOLTS MOUNTING THE CODERWEB PRINTING SPECIAL WEB PRINTING APPLICATIONS WEB PRINTINGPRINTING ON NARROW WEB MATERIALS PRINTING DIRECTLY ON MASTER ROLLSWEB PRINTING GANG MOUNTINGCARTON ALIGNMENT CARTON PRINTINGUniversal Non-Porous Conveyor Line Printers are designed so the frame of the machine will pivot on the mount- ing column. This allows the print drum to deflect, or swing, on contact with the leading edge of the carton a maximum of 2. It is recommended that cartons be aligned between guide rails with no more than 1/4 clearance on each side as shown in Figure 40. This should allow ample clearance for cartons and protect your printer from damage CARTON PRINTINGADJUST FOR DIE POSITIONING FOR INDEXING APPLICATIONSCARTON PRINTING 1/4” TO 3/8”CARTON PRINTING Although installing the printing dies in this position restricts how close to the leading edge of the carton you can register the print, it is one of the only ways to ensure a good imprint on every carton. Since the fastest drying non- porous inks will dry in approximately 2 seconds at 75 Degree F. ambient temperature, the ink will also dry on the die face within 2 seconds after it is applied by the transfer roll. If the dies have not contacted the carton surface before then, no imprint will be transferred to the cartonInk Cartridges MAINTENANCEPRE-INKING A NEW INK ROLL CLEANING THE CODER CLEANING THE TRANSFER ROLLDO NOT SUBMERGE THE TRANSFER ROLL IN SOLVENT MAINTENANCEMAINTENANCE CLEANING THE PRINTING DIESMAINTENANCE MOUNTING CONFIGURATION CONVERSION LEFTHAND/RIGHTHAND FIELD CONVERSIONPIVOT ARM & INKING SYSTEM ASSEMBLY CONVERSION MAINTENANCE TENSION ARM ASSEMBLY CONVERSIONMAINTENANCE PRINT DRUM INDEX MECHANISM CONVERSIONCONFIGURATION MAINTENANCEMAINTENANCE REPLACING PRINT DRUM INDEX SPRINGSRIGHT HAND CONFIGURATION LEFT HAND CONFIGURATIONMAINTENANCE REMOVING AND REPLACING INDEX BLOCK “B”2- Lift Index Block “B” straight up to remove MAINTENANCEMAINTENANCE INKING SYSTEM ASSEMBLYMAINTENANCE NON-POROUS CONVEYOR LINE PRINTER CE GUARD ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER CE GUARD ASSEMBLYNON-POROUS CONVEYOR LINE PRINTER ASSEMBLY CF-11 NON-POROUS CONVEYOR LINE PRINTER PARTS LISTNON-POROUS CONVEYOR LINE PRINTER INKING SYSTEM ASSEMBLY OPTIONAL THREADED PLUG WITH O-RING SEAL FOR RESERVOIR PORT NON-POROUS CONVEYOR LINE PRINTER INKING SYSTEM PARTS LISTNON-POROUS CONVEYOR LINE PRINTER PRINT DRUM ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER PRINT DRUM ASSEMBLYNON-POROUS CONVEYOR LINE PRINTER INDEX ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER INDEX ASSEMBLY