Manuals / Universal Laser Systems / Computer Equipment / Printer

Universal Laser Systems CLP-100NI-NPRT manual Quick Start

Models: CLP-100NI-NPRT

1 45

Download 45 pages 53.28 Kb

Page 13

The tops of the stainless pins will be flush with the top of the

QUICK START

11 -Replace the Knurled Drive Wheel “G” by aligning the 3 small holes with the 3 stainless drive pins on the top of the Transfer Roll “N” and pressing the Drive Wheel onto the Transfer Roll.

The tops of the stainless pins will be flush with the top of the

Drive Wheel when seated properly.

FIGURE 23

12 - Replace the Knurled Drive Wheel Cover “J” and rotate it into position with the flat edge directly facing the Print Drum.

Hold the Drive Wheel Cover and Inking System Cover in place.

FIGURE 24

13 - Replace the Knurled Cover Retaining Knob “K” and lightly tighten. Do not over tighten this knob or you may bend the top of the Knurled Drive Wheel Cover “J” and cause it to bind against the Knurled Drive Wheel. Now retighten the Pivot Arm Knurled Knob.

The Cover Retaining Knob should be just tight enough to keep the Inking System Assembly together and prevent the Drive Wheel Cover from rotating out of position.

FIGURE 25

13

Image 13

Universal Laser Systems CLP-100NI-NPRT manual Quick Start, The tops of the stainless pins will be flush with the top of the

Contents

OWNER’S MANUAL INSTALLATION - OPERATION - MAINTENANCESTENCILING & MARKING UNIVERSAL STENCILING & MARKING SYSTEMS, INCIMPORTANT NOTE LIMITED WARRANTYPREFACE CODER SPECIFICATIONSQUICK START PAGES 9 THRUCONVEYOR LINE PRINTER SPECIFICATIONS TOP MOUNT SERIES SPECIFICATIONSModel Shown CLP-100NI-NPRT Model Shown CLP-200NI-NPLS CONVEYOR LINE PRINTER SPECIFICATIONS SIDE MOUNT SERIESSPECIFICATIONS INDEXING AND NON-INDEXING MODELS MOUNTING CONFIGURATIONSPECIFICATIONS CODER MODELS DESIGNED FOR METRIC RIBtype PRINTING DIES RIBtype PRINTING DIESSPECIFICATIONS XF NEOPRENE INK ROLLS INK ROLLSTYPE MT INK ROLLS SPECIFICATIONSQUICK START INSTALLING THE INKING SYSTEM ASSEMBLYQUICK START INSTALLING THE PRE-INKED ROLLThe Knurled Drive Wheel Cover is very loose fitting QUICK START8 -Inspect the roll for excess surface wetness. Remove any excess ink by rolling the roll lightly over a piece of absorbent paper QUICK STARTQUICK START The tops of the stainless pins will be flush with the top of theQUICK START INSTALLING THE PRINTING DIESQUICK START ADJUSTING THE INK ROLL ECCENTRICFOR MOUNTING INSTRUCTIONS REFER TO THE APPROPRIATE SECTION FOR YOUR APPLICATION WEB PRINTING - PAGE CARTON PRINTING - PAGEBASIC PRINCIPLES OF OPERATION USING THE 4 OZ. RESERVOIR INK CARTRIDGESNON-POROUS INKING SYSTEM BASIC PRINCIPLES OF OPERATION SELECTING AN APPROPRIATE INKBASIC PRINCIPLES OF OPERATION INK DRYING TIME CONSIDERATIONSTRANSFER ROLLWEB PRINTING WEB PRINTING MOUNTING THE CODER3/8” BOLTS SPECIAL WEB PRINTING APPLICATIONS WEB PRINTINGPRINTING ON NARROW WEB MATERIALS PRINTING DIRECTLY ON MASTER ROLLSWEB PRINTING GANG MOUNTINGCARTON ALIGNMENT CARTON PRINTINGUniversal Non-Porous Conveyor Line Printers are designed so the frame of the machine will pivot on the mount- ing column. This allows the print drum to deflect, or swing, on contact with the leading edge of the carton a maximum of 2. It is recommended that cartons be aligned between guide rails with no more than 1/4 clearance on each side as shown in Figure 40. This should allow ample clearance for cartons and protect your printer from damage CARTON PRINTINGADJUST FOR DIE POSITIONING FOR INDEXING APPLICATIONSCARTON PRINTING 1/4” TO 3/8”CARTON PRINTING Although installing the printing dies in this position restricts how close to the leading edge of the carton you can register the print, it is one of the only ways to ensure a good imprint on every carton. Since the fastest drying non- porous inks will dry in approximately 2 seconds at 75 Degree F. ambient temperature, the ink will also dry on the die face within 2 seconds after it is applied by the transfer roll. If the dies have not contacted the carton surface before then, no imprint will be transferred to the cartonPRE-INKING A NEW INK ROLL MAINTENANCEInk Cartridges CLEANING THE CODER CLEANING THE TRANSFER ROLLDO NOT SUBMERGE THE TRANSFER ROLL IN SOLVENT MAINTENANCEMAINTENANCE CLEANING THE PRINTING DIESPIVOT ARM & INKING SYSTEM ASSEMBLY CONVERSION MOUNTING CONFIGURATION CONVERSION LEFTHAND/RIGHTHAND FIELD CONVERSIONMAINTENANCE MAINTENANCE TENSION ARM ASSEMBLY CONVERSIONMAINTENANCE PRINT DRUM INDEX MECHANISM CONVERSIONCONFIGURATION MAINTENANCEMAINTENANCE REPLACING PRINT DRUM INDEX SPRINGSRIGHT HAND CONFIGURATION LEFT HAND CONFIGURATIONMAINTENANCE REMOVING AND REPLACING INDEX BLOCK “B”2- Lift Index Block “B” straight up to remove MAINTENANCEMAINTENANCE INKING SYSTEM ASSEMBLYMAINTENANCE NON-POROUS CONVEYOR LINE PRINTER CE GUARD ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER CE GUARD ASSEMBLYNON-POROUS CONVEYOR LINE PRINTER ASSEMBLY CF-11 NON-POROUS CONVEYOR LINE PRINTER PARTS LISTNON-POROUS CONVEYOR LINE PRINTER INKING SYSTEM ASSEMBLY OPTIONAL THREADED PLUG WITH O-RING SEAL FOR RESERVOIR PORT NON-POROUS CONVEYOR LINE PRINTER INKING SYSTEM PARTS LISTNON-POROUS CONVEYOR LINE PRINTER PRINT DRUM ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER PRINT DRUM ASSEMBLYNON-POROUS CONVEYOR LINE PRINTER INDEX ASSEMBLY PARTS LIST NON-POROUS CONVEYOR LINE PRINTER INDEX ASSEMBLY