Vermont Casting SDDVRCCH Gasket Replacement, Inspect the Vent System Annually, Stove Disassembly

Models: SDDVRMB SDDVRBD, SDDVRC, SDDVRCCB SDDVRCB SDDVRCBS SDDVRCVG SDDVRCH SDDVRCB, SDDVREB, SDDVRMB, SDDVRBS, SDDVRCH, SDDVRVG, SDDVRBD, SDDVRCCB, SDDVRCH, SDDVRCVG, SDDVRCBD SDDVREB SDDVRCMB SDDVRVG SDDVRBS SDDVRCBD SDDVRCEB SDDVRCCH

1 52
Download 52 pages 34.35 Kb
Page 44
Image 44

Stardance Direct Vent - Rear Vent Gas Heaters

NOTE: Shown

without top for

clarity.

ST391a

Fig. 79 Release the latches to release the glass frame.

Gasket Replacement

The Stardance Gas Heater use a ‘tadpole’ type gasket to seal between the glass panel and the frame. In time, this gasket can become brittle and compressed and should be replaced. New gasket is available from your dealer.

Shut off the gas supply and allow the stove to cool. Wear safety goggles and a dust mask.

1.Remove the Front, Glass Frame and Glass Panel. (Figs. 78, 79) Remove the old gasket. Use a ra- zor blade to separate the glass and gasket from the frame, and to clean the glass of any remaining cement or bits of gasket. Use a cold chisel if neces- sary.

2.Determine the correct length of gasket by laying it out around the edge of the glass. Allow an extra 1

- 2” (25-50mm). Mark the spot to be cut. Use a utility knife.

3.Starting on a long edge, remove about 6” of the pro- tective paper strip and apply the flat adhesive face of the gasket around the outside-facing edge of the panel. Continue around the panel, applying about 6” at a time and being careful to not stretch the mate- rial. Do not overlap the gasket ends. (Fig. 80)

4.Apply a thin bead of high temperature silicone rubber sealant along the inside corner of the glass frame, all around the perimeter. Place the flat gasketed side of the glass panel back into the steel frame. Pinch the rounded inside-facing gasket mate- rial to bulk it up.

5.Replace the glass frame and front panel as previ- ously described.

ST179

Fig. 80 Wrap the gasket material around the outside edge of the glass.

Inspect the Vent System Annually

Have the vent system inspected annually by a quali- fied technician. Shut off the main gas supply before inspecting the system. Both the inner exhaust pipe and the outer combustion supply pipe must be checked to

confirm that they are unblocked and in good condition.

Check the Gas Flame Regularly

To ensure that the stove is operating properly, check the flames periodically to confirm that they match Fig- ure 81. The flames will be blue during the first 15-20 minutes of operation, and will gradually turn to yellow after that.

Do not use your stove if the flame pattern differs from that shown here. Contact your Vermont Castings dealer

or a qualified technician for help.

Figure 81

Stove Disassembly

If there is ever a need to remove the firebox assem- bly from the stove shell, support the firebox with solid stands about 6” (152 mm) tall under the left and right outer edges of the firebox base. Do not set the firebox assembly directly on the floor; this can damage the control valve and/or the gas lines from the valve to the firebox.

Before removing the firebox from the shell, disconnect the on/off switch wires from the valve. If the assembly includes the optional fan, disconnect the fan rheostat.

If the installation includes a wall thermostat, disconnect the thermostat leads from valve.

Disconnection and reconnection to the gas line should only be done by a qualified gas service technician.

Upon reinstallation, the vent system must be sealed to the firebox as shown in the installation section, Page

15.Also be sure the logs are placed in the firebox cor- rectly, as shown on Page 29.

44

20012950

Page 44
Image 44
Vermont Casting SDDVRCCH Gasket Replacement, Inspect the Vent System Annually, Check the Gas Flame Regularly, 20012950