Manuals / Woodstock / Power Tools / Saw

Woodstock owner manual Table of Contents, MODEL ST1000 SPECIFICATIONS, Maintenance

Models: ST1000

1 52

Download 52 pages 41.89 Kb

Page 3

Table of Contents

MODEL ST1000 SPECIFICATIONS	........................ 2
MACHINE FEATURES	3
SAFETY	4
Safety Instructions	4
POWER REQUIREMENTS	6
Operation	6
SETUP	7
Unpacking	7
Items Needed for Setup	7
Inventory	8
Cleanup	9
Site Considerations	9
Assembling Stand	10
Main Body	10
Motor & Switch	11
Installing Blade Guides	12
Table	13
Installing Positive Stop	13
Installing Fence	14
Dust Collection	15
Adjusting Positive Stop	15
Blade Tracking	16
Test Run	17
Tensioning Blade	17
Adjusting Support Bearings	18
Adjusting Blade Guides	19
Calibrating Table Tilt Scale	20
Aligning Table	21
Aligning Fence	21
Miter Gauge	22

OPERATIONS	23
Operation Safety	23
Overview	23
Key Switch	24
Guide Post	24
Blade Lead	25
Table Tilt	25
Ripping	26
Crosscutting	26
Resawing	27
Cutting Curves	28
Stacked Cuts	28
Blade Information	29
Blade Changes	31
MAINTENANCE	32
Schedule	32
Cleaning	32
Unpainted Cast Iron	32
Lubrication	32
SERVICE	33
Troubleshooting	33
Checking V-Belt	35
Tensioning V-Belt	35
Replacing V-Belt	36
Wheel Alignment	37
ST1000 Electrical Components	39
ST1000 Wiring Diagram	40
Main Breakdown	41
Main Breakdown Parts List	42
Fence Breakdown & Parts List	44
Safety Labels Breakdown & Parts List	45
WARRANTY	46
Warranty Registration	47

Image 3

Woodstock owner manual Table of Contents, MODEL ST1000 SPECIFICATIONS, Maintenance

Contents

14 BANDSAW MANUALPhone 360 734-3482 Online Technical Support tech-support@shopfox.biz MODEL ST1000Page Table of Contents MODEL ST1000 SPECIFICATIONSMAINTENANCE ST1000 14 Bandsaw MODEL ST1000 SPECIFICATIONSMACHINE FEATURES SAFETY Safety InstructionsZero Risk Does Not Exist 13. DISCONNECT POWER. Adjusting machine when it is connected to the power source greatly increases the risk of injury from acci- dental startup. Always disconnect power BEFORE doing any work on machine, includ- ing changing blades or other tooling Safety InstructionsCircuit Recommendations POWER REQUIREMENTSOperation Amperage DrawDESCRIPTION SETUPItems Needed for Setup UnpackingHardware InventoryMain Inventory Figure Fence Inventory FigureNecessary Space CleanupSite Considerations Floor LoadComponents and Hardware Needed To install the main bodyAssembling Stand Main BodyMotor & Switch To install the motor and switchComponents and Hardware Needed Guides Installing BladeTo install the lower blade guide To install the upper blade guide assemblyComponents and Hardware Needed Installing Positive StopTo install the table To install the positive stopInstalling Fence To install the fenceComponents and Hardware Needed To set the positive stop Adjusting Positive StopDust Collection To connect a dust collection hoseCENTER TRACKING Blade TrackingTo center track the blade Changes in the blade tension may change the blade trackingTo tension the bandsaw blade Test RunTensioning Blade To test run the machineTo adjust the support bearings Adjusting Support BearingsTo adjust the upper and lower blade guides Adjusting Blade GuidesTo calibrate the pointer on the table tilt scale Calibrating Table Tilt ScaleTo align the fence parallel with the miter slot Aligning TableAligning Fence To align the miter slot parallel to the bandsaw bladeTo calibrate the miter gauge Miter GaugeOverview Operation SafetyHere are some basic tips to follow when operat- ing the bandsaw OPERATIONSKey Switch To adjust guide post assembly alignment on the guide postGuide Post To skew your fence Blade LeadTable Tilt To correct blade leadTo crosscut with the Model ST1000 RippingCrosscutting To rip with the Model ST1000To resaw a workpiece Resawing1 1⁄ Cutting CurvesStacked Cuts WidthTooth Style Blade InformationBlade Length Blade WidthThe most common causes of blade breakage are Tooth PitchBlade Care Blade BreakageBlade Changes To remove the bladeTo replace the blade Unpainted Cast Iron MAINTENANCECleaning SchedulePROBLEM SERVICETroubleshooting MotorCORRECTIVE ACTION OperationPROBLEM POSSIBLE CAUSETools Needed Checking V-BeltTensioning V-Belt To check the V-beltHex Wrench 6mm Replacing V-BeltTo replace the V-belt Tools NeededTo verify if the upper and lower wheels are copla- nar Wheel AlignmentTo Shim a Wheel ST1000 Electrical Components 110V Motor Wiring 220V Motor WiringST1000 14 Bandsaw ST1000 Wiring DiagramST1000 14 Bandsaw Main BreakdownPART # Main Breakdown Parts ListPART # DESCRIPTIONPART # Main Breakdown Parts ListPART # DESCRIPTIONFence Breakdown & Parts List PART #DESCRIPTION Safety Labels Breakdown & Parts List PART #DESCRIPTION WARRANTY 9. Comments Warranty RegistrationPlace Stamp Here WOODSTOCK INTERNATIONAL INC P.O. BOX BELLINGHAM, WA