Manuals / Woodstock / Power Tools / Saw

Woodstock ST1000 Woodstock International Inc P.O. Box Bellingham, Wa, Place Stamp Here

Models: ST1000

1 52

Download 52 pages 41.89 Kb

Page 50

Image 50

FOLD ALONG DOTTED LINE

Place

Stamp

Here

WOODSTOCK INTERNATIONAL INC.

P.O. BOX 2309

BELLINGHAM, WA 98227-2309

FOLD ALONG DOTTED LINE

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Page 50

Image 50

Woodstock ST1000 owner manual Woodstock International Inc P.O. Box Bellingham, Wa, Place Stamp Here

Contents

MODEL ST1000 MANUALPhone 360 734-3482 Online Technical Support tech-support@shopfox.biz 14 BANDSAWPage MAINTENANCE Table of ContentsMODEL ST1000 SPECIFICATIONS MODEL ST1000 SPECIFICATIONS ST1000 14 BandsawMACHINE FEATURES Zero Risk Does Not Exist SAFETYSafety Instructions Safety Instructions 13. DISCONNECT POWER. Adjusting machine when it is connected to the power source greatly increases the risk of injury from acci- dental startup. Always disconnect power BEFORE doing any work on machine, includ- ing changing blades or other toolingAmperage Draw POWER REQUIREMENTSOperation Circuit RecommendationsUnpacking SETUPItems Needed for Setup DESCRIPTIONFence Inventory Figure InventoryMain Inventory Figure HardwareFloor Load CleanupSite Considerations Necessary SpaceMain Body To install the main bodyAssembling Stand Components and Hardware NeededComponents and Hardware Needed Motor & SwitchTo install the motor and switch To install the upper blade guide assembly Installing BladeTo install the lower blade guide GuidesTo install the positive stop Installing Positive StopTo install the table Components and Hardware NeededComponents and Hardware Needed Installing FenceTo install the fence To connect a dust collection hose Adjusting Positive StopDust Collection To set the positive stopChanges in the blade tension may change the blade tracking Blade TrackingTo center track the blade CENTER TRACKINGTo test run the machine Test RunTensioning Blade To tension the bandsaw bladeAdjusting Support Bearings To adjust the support bearingsAdjusting Blade Guides To adjust the upper and lower blade guidesCalibrating Table Tilt Scale To calibrate the pointer on the table tilt scaleTo align the miter slot parallel to the bandsaw blade Aligning TableAligning Fence To align the fence parallel with the miter slotMiter Gauge To calibrate the miter gaugeOPERATIONS Operation SafetyHere are some basic tips to follow when operat- ing the bandsaw OverviewGuide Post Key SwitchTo adjust guide post assembly alignment on the guide post To correct blade lead Blade LeadTable Tilt To skew your fenceTo rip with the Model ST1000 RippingCrosscutting To crosscut with the Model ST1000Resawing To resaw a workpieceWidth Cutting CurvesStacked Cuts 1 1⁄Blade Width Blade InformationBlade Length Tooth StyleBlade Breakage Tooth PitchBlade Care The most common causes of blade breakage areTo replace the blade Blade ChangesTo remove the blade Schedule MAINTENANCECleaning Unpainted Cast IronMotor SERVICETroubleshooting PROBLEMPOSSIBLE CAUSE OperationPROBLEM CORRECTIVE ACTIONTo check the V-belt Checking V-BeltTensioning V-Belt Tools NeededTools Needed Replacing V-BeltTo replace the V-belt Hex Wrench 6mmWheel Alignment To verify if the upper and lower wheels are copla- narTo Shim a Wheel 110V Motor Wiring 220V Motor Wiring ST1000 Electrical ComponentsST1000 Wiring Diagram ST1000 14 BandsawMain Breakdown ST1000 14 BandsawDESCRIPTION Main Breakdown Parts ListPART # PART #DESCRIPTION Main Breakdown Parts ListPART # PART #DESCRIPTION Fence Breakdown & Parts ListPART # DESCRIPTION Safety Labels Breakdown & Parts ListPART # WARRANTY Warranty Registration 9. CommentsWOODSTOCK INTERNATIONAL INC P.O. BOX BELLINGHAM, WA Place Stamp Here