Woodstock owner manual Manual, MODEL ST1000, Bandsaw, Owners, Printed in Taiwan

Models: ST1000

1 52

Page 1

MODEL ST1000	OWNER'S
14" BANDSAW	MANUAL

Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz

COPYRIGHT © MAY, 2006 BY WOODSTOCK INTERNATIONAL, INC.

	WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
#8302TR	THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.	Printed in Taiwan
#8302TR		Printed in Taiwan

Page 1

Image 1

Woodstock owner manual Manual, Phone 360 734-3482 Online Technical Support tech-support@shopfox.biz, MODEL ST1000

Contents

Phone 360 734-3482 Online Technical Support tech-support@shopfox.biz MANUALMODEL ST1000 14 BANDSAWPage MODEL ST1000 SPECIFICATIONS Table of ContentsMAINTENANCE ST1000 14 Bandsaw MODEL ST1000 SPECIFICATIONSMACHINE FEATURES Safety Instructions SAFETYZero Risk Does Not Exist 13. DISCONNECT POWER. Adjusting machine when it is connected to the power source greatly increases the risk of injury from acci- dental startup. Always disconnect power BEFORE doing any work on machine, includ- ing changing blades or other tooling Safety InstructionsOperation POWER REQUIREMENTSAmperage Draw Circuit RecommendationsItems Needed for Setup SETUPUnpacking DESCRIPTIONMain Inventory Figure InventoryFence Inventory Figure HardwareSite Considerations CleanupFloor Load Necessary SpaceAssembling Stand To install the main bodyMain Body Components and Hardware NeededTo install the motor and switch Motor & SwitchComponents and Hardware Needed To install the lower blade guide Installing BladeTo install the upper blade guide assembly GuidesTo install the table Installing Positive StopTo install the positive stop Components and Hardware NeededTo install the fence Installing FenceComponents and Hardware Needed Dust Collection Adjusting Positive StopTo connect a dust collection hose To set the positive stopTo center track the blade Blade TrackingChanges in the blade tension may change the blade tracking CENTER TRACKINGTensioning Blade Test RunTo test run the machine To tension the bandsaw bladeTo adjust the support bearings Adjusting Support BearingsTo adjust the upper and lower blade guides Adjusting Blade GuidesTo calibrate the pointer on the table tilt scale Calibrating Table Tilt ScaleAligning Fence Aligning TableTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slotTo calibrate the miter gauge Miter GaugeHere are some basic tips to follow when operat- ing the bandsaw Operation SafetyOPERATIONS OverviewTo adjust guide post assembly alignment on the guide post Key SwitchGuide Post Table Tilt Blade LeadTo correct blade lead To skew your fenceCrosscutting RippingTo rip with the Model ST1000 To crosscut with the Model ST1000To resaw a workpiece ResawingStacked Cuts Cutting CurvesWidth 1 1⁄Blade Length Blade InformationBlade Width Tooth StyleBlade Care Tooth PitchBlade Breakage The most common causes of blade breakage areTo remove the blade Blade ChangesTo replace the blade Cleaning MAINTENANCESchedule Unpainted Cast IronTroubleshooting SERVICEMotor PROBLEMPROBLEM OperationPOSSIBLE CAUSE CORRECTIVE ACTIONTensioning V-Belt Checking V-BeltTo check the V-belt Tools NeededTo replace the V-belt Replacing V-BeltTools Needed Hex Wrench 6mmTo verify if the upper and lower wheels are copla- nar Wheel AlignmentTo Shim a Wheel ST1000 Electrical Components 110V Motor Wiring 220V Motor WiringST1000 14 Bandsaw ST1000 Wiring DiagramST1000 14 Bandsaw Main BreakdownPART # Main Breakdown Parts ListDESCRIPTION PART #PART # Main Breakdown Parts ListDESCRIPTION PART #PART # Fence Breakdown & Parts ListDESCRIPTION PART # Safety Labels Breakdown & Parts ListDESCRIPTION WARRANTY 9. Comments Warranty RegistrationPlace Stamp Here WOODSTOCK INTERNATIONAL INC P.O. BOX BELLINGHAM, WA

MODEL ST1000

OWNER'S

14" BANDSAW

MANUAL

Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz

COPYRIGHT © MAY, 2006 BY WOODSTOCK INTERNATIONAL, INC.