Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology RS232-XPD manual Power Supply Settings

Models: RS232-XPD

1 60

Download 60 pages 29.02 Kb

Page 29

Installation and Configuration

Power Supply Settings

Power Supply Settings

For serial communication, the computer and the RS-232 interface must share the same communication settings. Make sure that the settings of the computer and of the power supply agree with those shown in Table 2.11.

Table 2.11 Power Supply Settings

Parameter	Setting
Transmission	Asynchronous

Mode	Full Duplex

Speeds	75, 150, 300, 600, 1200, 2400, 4800, 9600

Parity	None

Connector	DB9-pin Male

Start Bit	1

Stop Bit	1

Data Bits	8

Protocols	XON/XOFF
	CTS/RTS (DSR/DTR)
	NONE

Release 1.2

27

Image 29

Xantrex Technology RS232-XPD manual Power Supply Settings

Contents

Operating Manual Internal RS-232 Interface for XPD Series Programmable DC Power SupplyRS232-XPD Page Operating Manual for Internal RS-232 Interface for XPD 500 Watt SeriesProgrammable DC Power Supply Limited Warranty How do you get service?Proof of purchase may be in any one of the following forms Disclaimer Product WARNING Limitations on Use Information About Your Power SupplySafety PowerWarnings Cautions and Notes SupplyManual Revisions Main SectionsFeatures and Specifications Describes the interface and lists its features and specificationsAbout This Manual Operating Manual for RS-232 for XPD Series Power SupplyConfiguration Section Operation ContentsSection Features and Specifications Section Installation and Contents Description Section 1. Features and SpecificationsReadback Functions Features and FunctionsFeatures Features and Specifications SpecificationsModels 7.5-67Operating Manual for RS-232 for XPD Series Power Supply Features and SpecificationsSpecifications Initial Inspection Section 2. Installation and ConfigurationIntroduction Figure 2.1Power Supply Front Panel with RS-232 Interface Installed Installation and ConfigurationOperating Manual for RS-232 for XPD Series Power Supply Initial InspectionInitial Inspection Installation and ConfigurationLED INDICATORS Installation and ConfigurationInitial Inspection JUMPER SELECTIONBasic Setup Procedure Basic Setup ProcedureTable 2.2 Switch S1 Settings for Baud Rate Communications9600 4800To choose XON/XOFF protocol, select the XON switch position shown in Connections Use a 9-pin DB9 to 9-pin parallel cable to connect the interface card to the serial port on the host computer. If you need to use a 25-pin connector DB25 on the host interface, ensure the correct connections are made by referring Table 2.7. If the proper cables are not available and you need to change the transmit/receive pin configuration, see “Transmit / Receive Pin Selection” Remote/Local Operation RemoteStartup device-dependent commands available with this interface remote mode ExampleUse any command to do this REM ONFigure 2.4 RS-232 Connector J4 Pinouts default configuration RS-232 ConnectionPower Supply Settings Power Supply SettingsTable 2.12 OVP Control Mode Selection User Options and SettingsTTL You can use the Shutdown function to disable or enable the supplys output. Shutdown Disabling the supply using TTL shutdown allows you to make adjustments to the Figure 2.5 User Signals J21 Connector User SignalsTo install the ferrite block User Signals Installation and ConfigurationTo J21 Connector To User Custom Interface Operating Manual for RS-232 for XPD Series Power SupplySection 3. Operation Command SyntaxRS-232 Operation IntroductionMASK FOLD ≠ MK FOLD MASK FOLD = mask foldMASK FOLD ≠ MASK FD MASK FOLD = MASKExample Table 3.1 Command ParametersTable 3.2 Floating Point Numbers ISET 2.0A VSET ISET 2.0A VSETCOMMAND parameter COMMAND parameter, parameterLF Command Command SummaryOperation DescriptionDescription Query CommandsOperation Operation Calibration CommandsDescription Descriptionread. See “Accumulated Status, Status, and Fault Registers” on page Command ReferenceCommand OperationDescription CommandOperation Lockout. See also “Remote/Local Operation” on page CommandOperation DescriptionCommand Status, and Fault Registers” on page 47. Mnemonics are separated frompage Operation“Remote/Local Operation” on page CommandOperation Description“Accumulated Status, Status, and Fault Registers” on page Status, and Fault Registers” on pagestatus and fault registers See “Accumulated Status, Status, and Fault CommandOperation CommandDescription programmed voltage range. Refer to the output value as VRLO and record itAccumulated Status, Status, and Fault Registers Accumulated Status, Status, and Fault RegistersOperation Bit WeightCondition MnemonicERROR # Error CodesERROR IDENTIFICATION OperationLEDs TroubleshootingIntroduction Section 4. CalibrationSetup Voltage Mode CalibrationVoltage Program Calibration Procedure VoltageVoltage Readback Calibration Procedure Current Program Calibration Procedure Current Mode CalibrationCurrent Calibration Setup Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page 8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 Xantrex Technology Inc604 422 8595 Tel 604 421 3056 Fax 800 667 8422 Toll Free North America prg.info@xantrex.com