Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology RS232-XPD manual Operating Manual

Models: RS232-XPD

1 60

Download 60 pages 29.02 Kb

Page 1

RS232-XPD

RS232-XPD

Operating Manual

Internal RS-232 Interface for XPD Series Programmable DC Power Supply

Image 1

Xantrex Technology RS232-XPD manual Internal RS-232 Interface for XPD Series Programmable DC Power Supply

Contents

RS232-XPD Internal RS-232 Interface for XPD Series Programmable DC Power SupplyOperating Manual Page Programmable DC Power Supply Internal RS-232 Interface for XPD 500 Watt SeriesOperating Manual for Limited Warranty How do you get service?Proof of purchase may be in any one of the following forms Disclaimer Product WARNING Limitations on Use Information About Your Power SupplySafety PowerWarnings Cautions and Notes SupplyManual Revisions Main SectionsFeatures and Specifications Describes the interface and lists its features and specificationsAbout This Manual Operating Manual for RS-232 for XPD Series Power SupplySection Features and Specifications Section Installation and ContentsConfiguration Section Operation Contents Description Section 1. Features and SpecificationsFeatures Features and FunctionsReadback Functions Features and Specifications SpecificationsModels 7.5-67Specifications Features and SpecificationsOperating Manual for RS-232 for XPD Series Power Supply Introduction Section 2. Installation and ConfigurationInitial Inspection Figure 2.1Power Supply Front Panel with RS-232 Interface Installed Installation and ConfigurationOperating Manual for RS-232 for XPD Series Power Supply Initial InspectionInitial Inspection Installation and ConfigurationLED INDICATORS Installation and ConfigurationInitial Inspection JUMPER SELECTIONBasic Setup Procedure Basic Setup ProcedureTable 2.2 Switch S1 Settings for Baud Rate Communications9600 4800To choose XON/XOFF protocol, select the XON switch position shown in Connections Use a 9-pin DB9 to 9-pin parallel cable to connect the interface card to the serial port on the host computer. If you need to use a 25-pin connector DB25 on the host interface, ensure the correct connections are made by referring Table 2.7. If the proper cables are not available and you need to change the transmit/receive pin configuration, see “Transmit / Receive Pin Selection” Startup RemoteRemote/Local Operation device-dependent commands available with this interface remote mode ExampleUse any command to do this REM ONFigure 2.4 RS-232 Connector J4 Pinouts default configuration RS-232 ConnectionPower Supply Settings Power Supply SettingsTable 2.12 OVP Control Mode Selection User Options and SettingsTTL You can use the Shutdown function to disable or enable the supplys output. Shutdown Disabling the supply using TTL shutdown allows you to make adjustments to the Figure 2.5 User Signals J21 Connector User SignalsTo install the ferrite block User Signals Installation and ConfigurationTo J21 Connector To User Custom Interface Operating Manual for RS-232 for XPD Series Power SupplySection 3. Operation Command SyntaxRS-232 Operation IntroductionMASK FOLD ≠ MK FOLD MASK FOLD = mask foldMASK FOLD ≠ MASK FD MASK FOLD = MASKExample Table 3.1 Command ParametersTable 3.2 Floating Point Numbers ISET 2.0A VSET ISET 2.0A VSETCOMMAND parameter COMMAND parameter, parameterLF Command Command SummaryOperation DescriptionOperation Query CommandsDescription Operation Calibration CommandsDescription Descriptionread. See “Accumulated Status, Status, and Fault Registers” on page Command ReferenceCommand OperationOperation CommandDescription Lockout. See also “Remote/Local Operation” on page CommandOperation DescriptionCommand Status, and Fault Registers” on page 47. Mnemonics are separated frompage Operation“Remote/Local Operation” on page CommandOperation Description“Accumulated Status, Status, and Fault Registers” on page Status, and Fault Registers” on pagestatus and fault registers See “Accumulated Status, Status, and Fault CommandOperation CommandDescription programmed voltage range. Refer to the output value as VRLO and record itAccumulated Status, Status, and Fault Registers Accumulated Status, Status, and Fault RegistersOperation Bit WeightCondition MnemonicERROR # Error CodesERROR IDENTIFICATION OperationLEDs TroubleshootingIntroduction Section 4. CalibrationSetup Voltage Mode CalibrationVoltage Program Calibration Procedure VoltageVoltage Readback Calibration Procedure Current Calibration Setup Current Mode CalibrationCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page 8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 Xantrex Technology Inc604 422 8595 Tel 604 421 3056 Fax 800 667 8422 Toll Free North America prg.info@xantrex.com