Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology RS232-XPD manual Internal RS-232 Interface for XPD 500 Watt Series

Models: RS232-XPD

1 60

Download 60 pages 29.02 Kb

Page 3

Operating Manual for

Internal RS-232 Interface for XPD 500 Watt Series

Programmable DC

Power Supply

Image 3

Xantrex Technology RS232-XPD manual Internal RS-232 Interface for XPD 500 Watt Series, Operating Manual for

Contents

Internal RS-232 Interface for XPD Series Programmable DC Power Supply RS232-XPDOperating Manual Page Internal RS-232 Interface for XPD 500 Watt Series Programmable DC Power SupplyOperating Manual for Limited Warranty How do you get service?Proof of purchase may be in any one of the following forms Disclaimer Product WARNING Limitations on Use Information About Your Power SupplySupply PowerSafety Warnings Cautions and Notesfeatures and specifications Main SectionsManual Revisions Features and Specifications Describes the interface and lists itsAbout This Manual Operating Manual for RS-232 for XPD Series Power SupplyContents Section Features and Specifications Section Installation andConfiguration Section Operation Contents Description Section 1. Features and SpecificationsFeatures and Functions FeaturesReadback Functions 7.5-67 SpecificationsFeatures and Specifications ModelsFeatures and Specifications SpecificationsOperating Manual for RS-232 for XPD Series Power Supply Section 2. Installation and Configuration IntroductionInitial Inspection Initial Inspection Installation and ConfigurationFigure 2.1Power Supply Front Panel with RS-232 Interface Installed Operating Manual for RS-232 for XPD Series Power SupplyInitial Inspection Installation and ConfigurationJUMPER SELECTION Installation and ConfigurationLED INDICATORS Initial InspectionBasic Setup Procedure Basic Setup Procedure4800 CommunicationsTable 2.2 Switch S1 Settings for Baud Rate 9600To choose XON/XOFF protocol, select the XON switch position shown in Connections Use a 9-pin DB9 to 9-pin parallel cable to connect the interface card to the serial port on the host computer. If you need to use a 25-pin connector DB25 on the host interface, ensure the correct connections are made by referring Table 2.7. If the proper cables are not available and you need to change the transmit/receive pin configuration, see “Transmit / Receive Pin Selection” Remote StartupRemote/Local Operation device-dependent commands available with this interface remote mode ExampleUse any command to do this REM ONFigure 2.4 RS-232 Connector J4 Pinouts default configuration RS-232 ConnectionPower Supply Settings Power Supply SettingsTable 2.12 OVP Control Mode Selection User Options and SettingsTTL You can use the Shutdown function to disable or enable the supplys output. Shutdown Disabling the supply using TTL shutdown allows you to make adjustments to the Figure 2.5 User Signals J21 Connector User SignalsTo install the ferrite block Operating Manual for RS-232 for XPD Series Power Supply Installation and ConfigurationUser Signals To J21 Connector To User Custom InterfaceIntroduction Command SyntaxSection 3. Operation RS-232 OperationMASK FOLD = MASK MASK FOLD = mask foldMASK FOLD ≠ MK FOLD MASK FOLD ≠ MASK FDISET 2.0A VSET ISET 2.0A VSET Table 3.1 Command ParametersExample Table 3.2 Floating Point NumbersCOMMAND parameter COMMAND parameter, parameterLF Description Command SummaryCommand OperationQuery Commands OperationDescription Description Calibration CommandsOperation DescriptionOperation Command Referenceread. See “Accumulated Status, Status, and Fault Registers” on page CommandCommand OperationDescription Description CommandLockout. See also “Remote/Local Operation” on page OperationOperation Status, and Fault Registers” on page 47. Mnemonics are separated fromCommand pageDescription Command“Remote/Local Operation” on page OperationCommand Status, and Fault Registers” on page“Accumulated Status, Status, and Fault Registers” on page status and fault registers See “Accumulated Status, Status, and Faultprogrammed voltage range. Refer to the output value as VRLO and record it CommandOperation DescriptionAccumulated Status, Status, and Fault Registers Accumulated Status, Status, and Fault RegistersMnemonic Bit WeightOperation ConditionOperation Error CodesERROR # ERROR IDENTIFICATIONLEDs TroubleshootingIntroduction Section 4. CalibrationVoltage SetupVoltage Program Calibration Procedure Voltage Mode CalibrationVoltage Readback Calibration Procedure Current Calibration Setup Current Program Calibration ProcedureCurrent Mode Calibration Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page 800 667 8422 Toll Free North America prg.info@xantrex.com Xantrex Technology Inc8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 604 422 8595 Tel 604 421 3056 Fax