Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology RS232-XPD manual Installation and Configuration, Initial Inspection

Models: RS232-XPD

1 60

Download 60 pages 29.02 Kb

Page 18

Installation and Configuration

Installation and Configuration

Initial Inspection

CAUTION

Use proper static control techniques to avoid damage to static-sensitive components on the printed circuit board.

Service Request LED (SRQ)

Only used for GPIB option

Remote LED (REM)

Figure 2.1Power Supply Front Panel with RS-232 Interface Installed

16	Operating Manual for RS-232 for XPD Series Power Supply

Image 18

Xantrex Technology RS232-XPD manual Installation and Configuration, Initial Inspection

Contents

Internal RS-232 Interface for XPD Series Programmable DC Power Supply RS232-XPDOperating Manual Page Internal RS-232 Interface for XPD 500 Watt Series Programmable DC Power SupplyOperating Manual for How do you get service? Limited WarrantyProof of purchase may be in any one of the following forms Disclaimer Product Information About Your Power Supply WARNING Limitations on UseWarnings Cautions and Notes PowerSafety SupplyFeatures and Specifications Describes the interface and lists its Main SectionsManual Revisions features and specificationsOperating Manual for RS-232 for XPD Series Power Supply About This ManualContents Section Features and Specifications Section Installation andConfiguration Section Operation Contents Section 1. Features and Specifications DescriptionFeatures and Functions FeaturesReadback Functions Models SpecificationsFeatures and Specifications 7.5-67Features and Specifications SpecificationsOperating Manual for RS-232 for XPD Series Power Supply Section 2. Installation and Configuration IntroductionInitial Inspection Operating Manual for RS-232 for XPD Series Power Supply Installation and ConfigurationFigure 2.1Power Supply Front Panel with RS-232 Interface Installed Initial InspectionInstallation and Configuration Initial InspectionInitial Inspection Installation and ConfigurationLED INDICATORS JUMPER SELECTIONBasic Setup Procedure Basic Setup Procedure9600 CommunicationsTable 2.2 Switch S1 Settings for Baud Rate 4800To choose XON/XOFF protocol, select the XON switch position shown in Connections Use a 9-pin DB9 to 9-pin parallel cable to connect the interface card to the serial port on the host computer. If you need to use a 25-pin connector DB25 on the host interface, ensure the correct connections are made by referring Table 2.7. If the proper cables are not available and you need to change the transmit/receive pin configuration, see “Transmit / Receive Pin Selection” Remote StartupRemote/Local Operation device-dependent commands available with this interface Use any command to do this Exampleremote mode REM ONRS-232 Connection Figure 2.4 RS-232 Connector J4 Pinouts default configurationPower Supply Settings Power Supply SettingsUser Options and Settings Table 2.12 OVP Control Mode SelectionTTL You can use the Shutdown function to disable or enable the supplys output. Shutdown Disabling the supply using TTL shutdown allows you to make adjustments to the User Signals Figure 2.5 User Signals J21 ConnectorTo install the ferrite block To J21 Connector To User Custom Interface Installation and ConfigurationUser Signals Operating Manual for RS-232 for XPD Series Power SupplyRS-232 Operation Command SyntaxSection 3. Operation IntroductionMASK FOLD ≠ MASK FD MASK FOLD = mask foldMASK FOLD ≠ MK FOLD MASK FOLD = MASKTable 3.2 Floating Point Numbers Table 3.1 Command ParametersExample ISET 2.0A VSET ISET 2.0A VSETCOMMAND parameter COMMAND parameter, parameterLF Operation Command SummaryCommand DescriptionQuery Commands OperationDescription Description Calibration CommandsOperation DescriptionCommand Command Referenceread. See “Accumulated Status, Status, and Fault Registers” on page OperationCommand OperationDescription Operation CommandLockout. See also “Remote/Local Operation” on page Descriptionpage Status, and Fault Registers” on page 47. Mnemonics are separated fromCommand OperationOperation Command“Remote/Local Operation” on page Descriptionstatus and fault registers See “Accumulated Status, Status, and Fault Status, and Fault Registers” on page“Accumulated Status, Status, and Fault Registers” on page CommandDescription CommandOperation programmed voltage range. Refer to the output value as VRLO and record itAccumulated Status, Status, and Fault Registers Accumulated Status, Status, and Fault RegistersCondition Bit WeightOperation MnemonicERROR IDENTIFICATION Error CodesERROR # OperationTroubleshooting LEDsSection 4. Calibration IntroductionVoltage Program Calibration Procedure Voltage Mode CalibrationSetup VoltageVoltage Readback Calibration Procedure Current Mode Calibration Current Calibration SetupCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page 604 422 8595 Tel 604 421 3056 Fax Xantrex Technology Inc8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 800 667 8422 Toll Free North America prg.info@xantrex.com