Operator Guide Paper and other stock | Xerox 75 MX specs

Operator Guide

Paper and other stock

c = Requires a Xerox technical specialist to permanently set up any of the trays 1-4 to handle 12 x 18-inch (305 x 457 mm) paper. After any one of these trays is set up to handle this size, it cannot run other sizes. Tray 5, however, can be used without any special set-up intervention from Xerox.

d = For the correct paper loading orientation refer to the paper tray label or to Table 5-6.

e = Embossed letterhead may cause degraded paper handling, and possibly minor image deletion defects near the embossed area on either side of the paper.

f = There is a lightweight paper feeding kit that is recommended when carbonless stock runs out of tray 6. This kit reduces the nip force in the paper feed and reduces the incidence of smudged or burst cells on the paper. This kit part number is 606K07180.

g = Performance is highly dependent on the quality of the coated paper. Frequent use of coated papers, especially lower quality papers, might cause increased contamination in the printer which could degrade the paper handling capability and the image quality performance for all papers.

h = Image deletion defects might occur near the perforation, especially if the perforation is parallel to the feed direction.

i = Two-sided printing (duplex) should not be selected when this stock is used.

j = It is recommend that only Bypass Tray (Tray 5) is used for this stock.

k = Blank or preprinted covers are acceptable. Cannot print on textured cover stock.

l = The 110 lb index stock (203 gsm) and the 65 lb cover stock (244 gsm) are both used for covers on documents. The paper handling performance for both stocks will be similar.

NOTE: For all trays, the fusing quality and “fix level” for images on 65 lb. cover stock, Vellum Bristol papers, and other textured- surface stock will be degraded; therefore, this stock is not recommended for imaging use.

NOTE: Long Edge Feed (LEF) and Short Edge Feed (SEF) indicate the orientation of the sheet in a Paper Tray and which edge of the paper will be fed into the printer first.

DocuTech/DocuPrint 75/90 and DocuPrint 75 MX

5-5

Image 63

Xerox 75 MX manual Operator Guide Paper and other stock

Contents

Xerox Document Services Platform USA Table of Contents Product overview Maintenance Paper and other stock Problem solving Table of Contents Operator Guide About this guide Powering down the system Contents RequirementsTelephone requirements USA FCC requirements Service requirements Industry Canada requirements For service in Canada call 800 Electromagnetic compatibility United StatesEuropean Union Introduction Operator Guide Hot surface symbol Symbology Heated surface symbol Energy Star Environmental Choice Labeling European Union declaration of conformity Safety notes Operator Guide Operator Guide Safety notes Check your understanding Question What is the Electricity at Work Regulation?Electricity at Work Regulation UK Regulation Question Is Xerox equipment safe? Answer AnswerPlaces a duty on all employers and self-employed persons to Manufacturers or suppliers of such electrical systems Your responsibility Question I require records of all tests Printer cautions Electrical safetyAdditional queries Printer Controller cautions Controller Power on/off indicator Printer power on/off indicator Printer ozone information Printer or controller emergency power off Printer operational safety Printer laser safety Safety notes Operator Guide Europe following number 01707 Page Controller components Hardware components Printer components Ultra 10/Ultra 30 controller components Paper trays trays Green or Gold colored areas act as markers Bypass tray tray Trays 1 High Capacity feeder tray Tray 5 Bypass Tray Performance capabilities Tray guides and loading paper Loading paper in the Bypass Tray Tray Loading paper in Trays Bypass Tray Changing the Tray 6 settingsLoading paper in the High Capacity Feeder Tray Bypass Tray here Changing the guides from 8.5 x 11 inches to A4 Finisher Top TrayStacker Tray Stapling Staple placement Peripheral hardware components Unloading the Stacker during printing Modems Controller softwarePage Controller power-on procedure Power-on procedures LED Printer power-on Printer power-on procedure Printer Power-Off Using The Printer Switch Power-off proceduresPrinter power-off Printer power-off from the controller Printer power-off Printer Power-Off Using The Red Button Energy Saver Controller power-off Operator Guide Maintenance Ultra 10/Ultra 30 controller power-on button and LED Emergency power-off procedures Printer faults Clearing printer faultsPaper jams Jam clearance areas Finisher area Replaceable units and supplies 10. Access to area Replaceable items 11. Location of CRUs and supplies CRUs Ordering CRUs and other suppliesTelephone numbers for orders Supplies 6R1007 XE 6R90321 Dry Ink Toner usage and Dry Ink Low messageDry ink toner usage and area coverage 6R1006 Paper handling guidelines Performance information Size requirement for duplex printing General stapling guidelines Staple capability for various paper weights Performance tables Operator Guide Paper and other stock Printer performance for standard paper 20 lb Spanish Sp. Folio Printer performance for standard paper 80 gsm Xerox EuropeA4 Cover Foolscap GBC brand pre-punched Sameceda Printer performance for non-standard paper Other stocksTransparencies Labels Or 4 holes Recommendations for loading special stockRecommendations for loading special stock Hole-punched Edge Pre-printedLetterhead Reinforced Mylar Recommendations for handling, loading, and storing paper GBC stockSameceda Storing Loading and handling Avoiding the problems Problem solving Troubleshooting tips Solving the problems Handling Stock Problem solvingOperator Guide Calling the Welcome Center