Connecting the power cable, 27 En | Yamaha DSP-AX763 guide

Connecting the power cable

	C DVR
MONITOR OUT	C DVR

AC OUTLET

SWITCHED

100W MAX.

0.4A MAX.

To the AC wall outlet

■AC OUTLET (SWITCHED)

Use this outlet to supply power to any connected components. Connect the power cable of your other components to this outlet. Power to this outlet is supplied when this unit is turned on. However, power to this outlet is cut off when this unit is turned off or when

CSTANDBY/ON on the front panel is pressed. For information on the maximum power or the total power consumption of the components that can be connected to this outlet, see “Specifications” on page 109.

Note

The power to AC OUTLET of this unit is not cut off while this unit is charging connected iPod even when this unit is in the standby mode. When this unit completes charging or the iPod is disconnected, the power is cut off automatically when this unit is in the standby mode.

Memory back-up

The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, the stored data will be lost in case the power cable is disconnected from the AC wall outlet or if the power supply is cut off for more than one week.

Connections

Setting the speaker impedance

Caution

If you are to use 6 ohm speakers, set “SP IMP.” to “6ΩMIN” as follows BEFORE using this unit. 4 ohm speakers can be also used as the front speakers.

1Make sure this unit turned off.

See page 28 for details.

2Press and hold DTONE CONTROL and then press CSTANDBY/ON to turn on this

unit.

This unit turns on, and the advanced setup menu appears in the front panel display.

TONE CONTROL	While holding
	down	STANDBY
		/ON

3Rotate the EPROGRAM selector to select “SP IMP.”.

“SP IMP.” and the current speaker impedance setting (“8Ω MIN”) appear in the front panel display.

4Press DTONE CONTROL repeatedly to select “6ΩMIN”.

5Press CSTANDBY/ON to save the new setting and turn off this unit.

Note

The setting you made is reflected next time you turn on this unit.

PREPARATION

English

27 En

Image 29

Yamaha DSP-AX763 owner manual Connecting the power cable, Setting the speaker impedance, 27 En

Contents

DSP-AX763 Special Instructions for U.K. Model For U.K. customers Contents Supplied accessories Features About this manual BluetoothIPod Color Getting started Installing batteries in the remote control Quick start guide Set up your speakersPreparation Check the items Press Scene 1 button Place your speakers and subwoofer in the room Front speakers and center speaker Components into the AC wall outlet Connect the power plug of this unit and otherFor further connections Rotate Bvolume to adjust the volume Default assigned Scene templatesAbout Scene function Check the type of the connected speakers What do you want to do with this unit? 10 En ConnectionsRear panel Channel speaker layout Placing speakers11 En See page 14 for connection information 12 EnSurround back speaker Front left and right speakers Center speaker Subwoofers 13 En Using presence speakersTo 1 m 1 to 3 ft Ft or Higher For the 7.1-channel speaker setting Connecting speakers14 En Front a 15 En For the 6.1-channel speaker settingFor the 5.1-channel speaker setting Using bi-amplification connections Connecting the speaker cableTighten the knob to secure the wire 16 En 17 En Information on jacks and cable plugsAudio jacks Video jacks Information on Hdmi Hdmi signal compatibility18 En Hdmi jack and cable plug Audio signal flow Audio and video signal flowVideo signal flow 19 En 20 En Connecting a TV monitor or projector Connecting a DVD player Connecting other components21 En DVD player DVD recorder Or PVR Connecting a set-top box22 En 23 En Connecting audio componentsTurntable One for the audio connection 24 En Connecting an external amplifier 25 En Connecting a multi-format player or an external decoderYamaha iPod universal dock Or Bluetooth adapter Using Remote OUT jack Using the Video AUX jacks on the front panelInfrared signal Receiver or Yamaha Component 26 En 27 En Connecting the power cableSetting the speaker impedance Press CSTANDBY/ON or Epower to turn on this unit Set this unit to the standby modeTurning this unit on and off 28 En 29 En Front panel display 30 En Using the remote control 31 En Using Auto SetupMIC on View OSD menu appears in the front panel display Make sure of the following check points 32 En 33 En 34 En Press 9ENTER to display the setup results in detailPress 9k / n to toggle between the parameters in a results Press 9ENTER to return to the top result display If Warning appears If an error screen appears35 En 36 En Selecting the Scene templatesPress and hold the Jscene or 4SCENE button for 3 seconds Selected Scene template is assigned to the Scene button LP Record Listening 37 EnWhich Scene template would you like to select? 38 En Preset Scene templates descriptions 39 En Creating your original Scene templatesRename the Scene templates Press the 4SCENE button again to confirm the edit Controlling the input source Components in the Scene mode Using the remote control for the Scene featureTransmit indicator 2 flashes twice 40 En 41 En Basic procedurePlayback Selecting the Multi CH Input component Using the Zone B featureSelecting the front speaker set 42 En 43 En Selecting audio input jacks Press Gmute on the remote control to mute the audio output Using your headphonesMuting the audio output 44 En Displaying the input source information Hdmi error and message45 En Audio information Canceling the sleep timer Using the sleep timer46 En Lights up Sound field program descriptions Sound field programs47 En For audio music sources For movie sources 48 EnFor various sources Compressed Music Enhancer Surround decode mode49 En 50 En Deactivating the Straight modePress Fstraight or Kstraight to select Straight Sound effect is turned back on Adjusting the speaker level Using audio featuresAdjusting the tonal quality Enjoying pure hi-fi sound Remote control operation Using iPodControlling iPod in the simple remote Mode Controlling iPod 53 En Controlling iPod in the menu browse ModeFunction of the play information display Shuffle Shuffle Pairing by using SET Menu Using Bluetooth componentsQuick pairing 54 En 55 En Recording Changing sound field parameter settings Advanced sound configurations56 En Following screen is shown in the OSD Adjusting the vertical dialogue position DIALG.LIFT Basic configuration of sound field Programs57 En Increase the value of DSP Level Sound field parameter Features Sound field parameters for the advanced configurations58 En INIT.DLY SB INI.DLY Liveness S.LIVENESS SB Liveness 59 EnRoom Size P.ROOM Size S.ROOM Size SB Room Size 60 En REV.DELAYREV.TIME REV.LEVEL 61 En Selecting decodersSelecting decoders used with sound Field programs SUR Available decoders Decoder parameter descriptions 62 EnDecoder descriptions SUR Auto setup Auto Setup Customizing this unit Manual SetupManual setup Manual Setup 63 En 64 En Input menu 4 Input Menu 65 EnOption menu 5 Option Menu Adisplay SET DINIT. Config Signal information Signal Info66 En Ehdmi SET Press 9k / n to select Manual Setup Using SET MenuPress 9ENTER to enter Manual Setup 67 En 68 En Speaker settings Aspeaker SET 69 En 70 En Subwoofer phase Subwoofer PhaseSpeaker level BSP Level Bass cross over Cross Over 71 En Unit for the speaker distance adjustment UnitSpeaker distance CSP Distance Speaker distances 72 En Equalizer Aequalizer 73 EnEqualizer type select EQ Type Select Graphic equalizer GEQ 74 En Headphones HeadphoneLow-frequency effect level Speakers Speaker Extended surround Eextd SUR 75 EnAudio and video synchronization Lip sync Dlipsync 76 En Use this menu to adjust the parameters of each input sourceInput/output assignment Assignment 77 En Decoder mode Decoder ModeInput rename Input Rename Charge on standby Standby Charge 78 En 79 En Display settings Adisplay SET 80 En Video settings Bvideo SETVideo conversion Video Conv Memory guard Cmemory Guard 81 En Initial configuration DINIT. ConfigAudio select Audio Select Extended surround Extd SUR Controlling this unit, a TV, or other components Remote control features82 En Controlling this unit Controlling other components 83 En Controlling optional components Option mode Setting remote control codesRemote control code default settings 84 En 85 En Press Clearn again to exit from the setup modePress 9ENTER Press 9ENTER to set the number Press Clearn using a ballpoint pen or similar object Programming codes from other remote controlsLearn appears in the display window 6 on Remote control 86 En Press Crename using a ballpoint pen or similar object Press Clearn again to exit the learning modeChanging source names in the display window 87 En Macro operations Macro programming features88 En To automatically transmit these signals in order Default macro functions89 En Pressing Macro button Programming macro operations 90 En Press 9k / n to select the clear mode Clearing configurations91 En Clearing function sets Clearing a learned function 92 EnSelected component name appears in the display window Press Clearn again to exit Clearing a macro function Press Cmacro again to exit the macro programming mode93 En Using the advanced setup Advanced setup94 En Speaker impedance SP IMP Setting remote control AMP ID codes Remote control AMP ID Remote AMPSet the operation mode selector to Famp or Remote control AMP ID codes Scene IR code setting Scene IR Bi-amplifier setting BI-AMP96 En Parameter initialization Init Problem Cause Remedy See Troubleshooting97 En General 98 En 99 En Does not work or 100 EnFunction properly Does not learn new IPod Bluetooth101 En 102 En Before Auto SetupDuring Auto Setup 1OUT of Phase After Auto Setup3LEVEL Error 103 En 104 En Resetting the system 105 En Glossary 106 En 107 En 108 En Sound field program informationElements of a sound field Early reflections 109 En Specifications Numerics Index110 En 111 En 112 En Aspeakers or 5DVD 113 EnSurround PRE OUT Conditions 114 En Speakers Front panel Volume Remote control HD DVD Player IiiBlu-lay Disc player Satellite Tuner Cathay VCR WN24880 DSP-AX863SE/DSP-AX763 Title