103 En, After Auto Setup, 1OUT of Phase | Yamaha DSP-AX763 manual

Troubleshooting

After AUTO SETUP

	Warning message	Cause	Remedy	See
	Warning message	Cause	Remedy	page
				page

W-1:OUT OF PHASE	Speaker polarity is not correct. This message
	may appear depending on the speakers even
	when the speakers are connected correctly.

Check the speaker connections for proper	14
polarity (+ or –).

W-2:OVER 24m (80ft)	The distance between the speaker and the	Bring the speaker closer to the listening	—
	listening position is over 24 m (80 ft).	position.

W-3:LEVEL ERROR	The difference of volume level among	Readjust the speaker installation so that all	—
	speakers is excessive.	speakers are set in locations with similar
		conditions.

		Check the speaker connections.	14

		Use speakers of similar quality.	—

		When “SWFR: TOO LOUD” or “SWFR:	31
		TOO LOW” appears in the result screen, the
		output volume of the subwoofer.

W-4:CHECK PRNS	“EXTRA SP ASSIGN” is set to
	“PRESENCE”, though the presence channel
	signals are not detected.

Check the presence speaker connections.	14
Set “EXTRA SP ASSIGN” to a setting other	32
than “PRESENCE”.

Notes

•If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.

•If a warning message “W-1”, “W-2”, or “W-3” appears, corrections are made, but they may not be optimal.

•If an error message “E-10” occurs repeatedly, contact a qualified Yamaha service center.

INFORMATION	ADDITIONAL

English

103 En

Image 105

Yamaha DSP-AX763 owner manual 103 En, After Auto Setup, 1OUT of Phase, 3LEVEL Error, 4CHECK Prns

Contents

DSP-AX763 Special Instructions for U.K. Model For U.K. customers Contents Supplied accessories Features About this manual BluetoothIPod Color Getting started Installing batteries in the remote control Quick start guide Set up your speakersPreparation Check the items Press Scene 1 button Place your speakers and subwoofer in the room Front speakers and center speaker Connect the power plug of this unit and other For further connectionsComponents into the AC wall outlet Rotate Bvolume to adjust the volume Default assigned Scene templatesAbout Scene function Check the type of the connected speakers What do you want to do with this unit? Connections Rear panel10 En Placing speakers 11 EnChannel speaker layout See page 14 for connection information 12 EnSurround back speaker Front left and right speakers Center speaker Subwoofers 13 En Using presence speakersTo 1 m 1 to 3 ft Ft or Higher For the 7.1-channel speaker setting Connecting speakers14 En Front a For the 6.1-channel speaker setting For the 5.1-channel speaker setting15 En Using bi-amplification connections Connecting the speaker cableTighten the knob to secure the wire 16 En 17 En Information on jacks and cable plugsAudio jacks Video jacks Information on Hdmi Hdmi signal compatibility18 En Hdmi jack and cable plug Audio signal flow Audio and video signal flowVideo signal flow 19 En 20 En Connecting a TV monitor or projector Connecting a DVD player Connecting other components21 En DVD player Connecting a set-top box 22 EnDVD recorder Or PVR 23 En Connecting audio componentsTurntable One for the audio connection 24 En Connecting an external amplifier Connecting a multi-format player or an external decoder Yamaha iPod universal dock Or Bluetooth adapter25 En Using Remote OUT jack Using the Video AUX jacks on the front panelInfrared signal Receiver or Yamaha Component 26 En Connecting the power cable Setting the speaker impedance27 En Press CSTANDBY/ON or Epower to turn on this unit Set this unit to the standby modeTurning this unit on and off 28 En 29 En Front panel display 30 En Using the remote control 31 En Using Auto SetupMIC on View OSD menu appears in the front panel display Make sure of the following check points 32 En 33 En 34 En Press 9ENTER to display the setup results in detailPress 9k / n to toggle between the parameters in a results Press 9ENTER to return to the top result display If an error screen appears 35 EnIf Warning appears 36 En Selecting the Scene templatesPress and hold the Jscene or 4SCENE button for 3 seconds Selected Scene template is assigned to the Scene button 37 En Which Scene template would you like to select?LP Record Listening 38 En Preset Scene templates descriptions 39 En Creating your original Scene templatesRename the Scene templates Press the 4SCENE button again to confirm the edit Controlling the input source Components in the Scene mode Using the remote control for the Scene featureTransmit indicator 2 flashes twice 40 En Basic procedure Playback41 En Selecting the Multi CH Input component Using the Zone B featureSelecting the front speaker set 42 En 43 En Selecting audio input jacks Press Gmute on the remote control to mute the audio output Using your headphonesMuting the audio output 44 En Displaying the input source information Hdmi error and message45 En Audio information Canceling the sleep timer Using the sleep timer46 En Lights up Sound field program descriptions Sound field programs47 En For audio music sources 48 En For various sourcesFor movie sources Surround decode mode 49 EnCompressed Music Enhancer 50 En Deactivating the Straight modePress Fstraight or Kstraight to select Straight Sound effect is turned back on Adjusting the speaker level Using audio featuresAdjusting the tonal quality Enjoying pure hi-fi sound Remote control operation Using iPodControlling iPod in the simple remote Mode Controlling iPod 53 En Controlling iPod in the menu browse ModeFunction of the play information display Shuffle Shuffle Pairing by using SET Menu Using Bluetooth componentsQuick pairing 54 En 55 En Recording Changing sound field parameter settings Advanced sound configurations56 En Following screen is shown in the OSD Adjusting the vertical dialogue position DIALG.LIFT Basic configuration of sound field Programs57 En Increase the value of DSP Level Sound field parameter Features Sound field parameters for the advanced configurations58 En INIT.DLY SB INI.DLY 59 En Room Size P.ROOM Size S.ROOM Size SB Room SizeLiveness S.LIVENESS SB Liveness 60 En REV.DELAYREV.TIME REV.LEVEL 61 En Selecting decodersSelecting decoders used with sound Field programs SUR Available decoders 62 En Decoder descriptions SURDecoder parameter descriptions Auto setup Auto Setup Customizing this unit Manual SetupManual setup Manual Setup 63 En 64 En Input menu 4 Input Menu 65 EnOption menu 5 Option Menu Adisplay SET DINIT. Config Signal information Signal Info66 En Ehdmi SET Press 9k / n to select Manual Setup Using SET MenuPress 9ENTER to enter Manual Setup 67 En 68 En Speaker settings Aspeaker SET 69 En 70 En Subwoofer phase Subwoofer PhaseSpeaker level BSP Level Bass cross over Cross Over 71 En Unit for the speaker distance adjustment UnitSpeaker distance CSP Distance Speaker distances 72 En Equalizer Aequalizer 73 EnEqualizer type select EQ Type Select Graphic equalizer GEQ 74 En Headphones HeadphoneLow-frequency effect level Speakers Speaker 75 En Audio and video synchronization Lip sync DlipsyncExtended surround Eextd SUR 76 En Use this menu to adjust the parameters of each input sourceInput/output assignment Assignment 77 En Decoder mode Decoder ModeInput rename Input Rename Charge on standby Standby Charge 78 En 79 En Display settings Adisplay SET 80 En Video settings Bvideo SETVideo conversion Video Conv Memory guard Cmemory Guard 81 En Initial configuration DINIT. ConfigAudio select Audio Select Extended surround Extd SUR Controlling this unit, a TV, or other components Remote control features82 En Controlling this unit Controlling other components 83 En Controlling optional components Option mode Setting remote control codesRemote control code default settings 84 En 85 En Press Clearn again to exit from the setup modePress 9ENTER Press 9ENTER to set the number Press Clearn using a ballpoint pen or similar object Programming codes from other remote controlsLearn appears in the display window 6 on Remote control 86 En Press Crename using a ballpoint pen or similar object Press Clearn again to exit the learning modeChanging source names in the display window 87 En Macro programming features 88 EnMacro operations To automatically transmit these signals in order Default macro functions89 En Pressing Macro button Programming macro operations 90 En Press 9k / n to select the clear mode Clearing configurations91 En Clearing function sets Clearing a learned function 92 EnSelected component name appears in the display window Press Clearn again to exit Press Cmacro again to exit the macro programming mode 93 EnClearing a macro function Using the advanced setup Advanced setup94 En Speaker impedance SP IMP Setting remote control AMP ID codes Remote control AMP ID Remote AMPSet the operation mode selector to Famp or Remote control AMP ID codes Scene IR code setting Scene IR Bi-amplifier setting BI-AMP96 En Parameter initialization Init Problem Cause Remedy See Troubleshooting97 En General 98 En 99 En Does not work or 100 EnFunction properly Does not learn new Bluetooth 101 EnIPod Before Auto Setup During Auto Setup102 En 1OUT of Phase After Auto Setup3LEVEL Error 103 En 104 En Resetting the system 105 En Glossary 106 En 107 En 108 En Sound field program informationElements of a sound field Early reflections 109 En Specifications Index 110 EnNumerics 111 En 112 En 113 En Surround PRE OUTAspeakers or 5DVD Conditions 114 En Speakers Front panel Volume Remote control Iii Blu-lay Disc playerHD DVD Player Satellite Tuner Cathay VCR WN24880 DSP-AX863SE/DSP-AX763 Title