Yamaha M2500, Yamaha Mixing Consol Midi channel, Program change transmission/reception OFF/on/LoC

The Scene Memory function

.......................................(MIDI channel) 1–16

(factory setting: “”)

Select the MIDI channel that will be used when MIDI data is transmitted/received via the MIDI IN/OUT connectors.

(program change transmission/reception) ...

....oFF/on/LoC

(factory setting: “”)

This specifies whether or not program change mes- sages will be transmitted/received via the MIDI IN/ OUT connectors.

•If “ ” is selected

Program changes will not be transmitted or received.

•If ” is selected

Program changes will be transmitted and received.

–When program changes 0–127 are received at the MIDI IN connector, scene memory numbers 1–128

will be recalled. (However if the utility item “Recall

operation” is set to “,” program changes 0–7 will be ignored.)

–When you recall a scene memory number 1–128 in which a scene has been stored, a program change 0–127 will be transmitted from the MIDI OUT

connector. (Even if the Utility item “Recall Opera-

tion” is set to “,” you can use the 0–9/ENTER and RECALL switches to transmit program changes 0–7 from the MIDI OUT connector.)

•If “ ” is selected

Program changes will be transmitted and received.

–Program changes will be received in the same way as for the “” setting.

–Even when you recall a scene memory number 1– 128 in which no scene has been stored, a program change 0–127 will be transmitted from the MIDI OUT connector.

(control change transmission/reception)......

.... oFF/GrP/on

(factory setting: “”)

Specify whether control change messages will be transmitted/received via the MIDI IN/OUT connec- tors.

•If “ ” is selected

Control change messages will not be transmitted or received.

•If ” is selected

Control change messages will be transmitted and received.

–When control change numbers 1–70 are received, the corresponding channel will be switched on/off. When mute groups are used, control change num- bers 105–112 will switch mute groups 1–8 on/off. (For details refer to the following section “Control change table.”)

•If “ ” is selected

Only the control change numbers (105–112) that correspond to mute groups 1–8 will be transmitted and received.

(program change reception omni on/off).....

.............on/oFF

(factory setting: “”)

Specify whether or not the MIDI channel specified by the Utility item CH will be used when receiving pro- gram change messages.

•If ” is selected

Program change messages will be received on all MIDI channels (1–16).

•If “ ” is selected

Program change messages will be received only on the MIDI channel specified by the Utility item CH.

..........................................(echo back) on/oFF

(factory setting: “”)

Specify whether messages received at the MIDI IN connector will be echoed back from the MIDI OUT connector. If this is turned “,” messages will be echoed back. However if a bulk dump request is received, that message itself will not be echoed; rather, the bulk dump data will be transmitted.

(bulk out).......................................ALL/1–128

Transmit the contents of scene memory from the MIDI OUT connector as MIDI bulk dump data. Specify the desired value and press the STORE switch, and the bulk data dump will begin. While the data is being transmitted, the MEMORY display will

indicate “ .”

•If “ ” is selected

Bulk dump data for all scene memory numbers (1– 128) will be transmitted.

• If “ ”– ” is selected

Bulk dump data for the corresponding scene memory number (1–128) will be transmitted.

(bulk dump request) .....................ALL/1–128

Transmit a message (bulk dump request) from the MIDI OUT connector to request transmission of bulk dump data. If another M2500 unit is connected via its MIDI IN/OUT connectors, the scene memory contents of the other M2500 will be copied to the first M2500. Specify the value and press the STORE key to transmit the bulk dump request.

•If “ ” is selected

A bulk dump request for all scene memories will be transmitted.

• If “ ”– ” is selected

A bulk dump request for the scene memory of the corresponding number (1–128) will be transmitted.

M2500—Owner’s Manual 35