Fader, AFL after fader listen switch | Yamaha M2500 specification

Control panel

F ON/EDIT switch / ON, CHECK indicators

The function of this switch and these indicators will change depending on the mode of the M2500.

●In normal mode

You can use the ON/EDIT switch to turn each G1/ A7–G8/A14 channel on/off. When the channel is switched on/off, the ON indicator will be lit/dark to indicate the status. Channels that are switched off will not send any signals to the STEREO, MONO/C, or MATRIX buses.

●In check mode

When a scene (which contains the on/off state of the ON/EDIT switches) is selected, the on/off status memorized in that scene will be indicated by the lit/ dark status of the CHECK indicator. In check mode, you can also use the ON/EDIT switch to switch the CHECK indicator between lit/dark. (The current on/ off setting will not be affected.) For details on check mode, refer to page 32.

GFader

This adjusts the output level of the GRP/AUX OUT.

HAFL (after fader listen) switch

This switch allows you to monitor the signal of the G1/A7–G8/A14 section from the MONITOR OUT/ PHONES jacks. If the input channel PFL switches are all off, turning this AFL switch on (the indicator above the switch will light) will allow you to monitor the corresponding G1/A7–G8/A14 section signal from the MONITOR OUT/PHONES jacks. The monitor signal can be switched between pre/post- fader using the MASTER PFL switch of the monitor section.

1

GROUP

7

1

3

5

AUX

9

11 13

INSERT I/O

7

to METER

MATRIX

MONITOR

3

5

7

0dB

STEREO

STEREO

SUBIN

INPUT

MASTER

2

4

6

8

2

4

6

8

10 12 14

G1/A7

ST

ST

ST

G1/A7

L RMONO/C

G1/A7

G2/A8

G3/A9

G4/A10

G5/A11

G6/A12 G7/A13 G8/A14

L RMONO/C

L R

MONOL RON

MONOL RMONOL RON

GRP/AUX OUT

+4dB

PAN

ST

6

4 MONO

LCR

CHECK

ON

MATRIX

5

Control

ON/EDIT

from CPU

AFL 8

to METER

AUX/GRP OUT

+4dB

LEVEL

ON

A7/G1

1

2

AFL

3

GRP/AUX G2/A8-G8/A14

and

AUX/GRP A8/G2-A14/G8

Same as

G1/A7

and

G7/A1

GROUP

AUX

GROUP/AUX FLIP

M2500—Owner’s Manual 13

Image 17

Yamaha M2500, Yamaha Mixing Consol owner manual Fader, AFL after fader listen switch

Contents

Mixing Console Nederland Netherlands Operating Notes Important InformationKeep This Manual For Future Reference Read the Following Before Operating M2500Page Introduction Contents Features of the system Input channel section Control panelMonaural input channels AUX 1-AUX 14 controls PAN control PRE switchesChannel assign switches PEAK/NOM/SIGNAL indicators ON/EDIT switch / ON, Check indicatorsPFL pre-fader listen switch Channel fader Gain B control B switchStereo input channels BAL control If the ST switch is onIf a 1-2/3-4/5-6/7-8 switch is on Input a ST CH Input B Mono GROUP/AUX master section AFL after fader listen switchesAUX 1-6 section AUX 1-6master faders AFL switch On switchGROUP/AUX Flip switch= Group GROUP/AUX Flip switch= AUX G1/A7-G8/A14 section Matrix switch Fader AFL after fader listen switch When AUX is selected GROUP/AUX Flip switchWhen Group is selected MATRIX/ST/MONO/LCR Stereo/monaural master section Matrix switchStereo section MONO/C section Matrix Monitor ST L/R controls Matrix sectionMONO/C control G1/A7-G8/A14 controls Master indicator Monitor signal priority orderMaster PFL switch Monitor section Phones jack +R switchPhones headphone control Oscillator on switch MONO/C switchTalkback/oscillator section MIC jack AUX 1-6 switch A7-14/G1-8 switchG1-8/A7-14 switch Meter select section Store switch Recall switchCheck switch Direct Recall 1-8 switches Phantom Master indicator +15V/-15V/+12V indicatorsMeter bridge MONO/C level meter Nominal input Rear panelInsert I/O jacks Input B jacks Stereo input channel input/ output jacksInput a jacks Input jacks AUX/GRP OUT jacks Master section input/output jacksGRP/AUX OUT jacks Matrix OUT jacks Monitor OUT jacks ST OUT, MONO/C OUT jacksSUB in Matrix jacks SUB in ST L/R, MONO/C jack Phantom Master switch Midi connectorsDC Power Input connector Lamp connector Modes of the scene memory function What is scene memory?Scene Memory function Using Direct Recall to recall a scene Operation in Normal modeRecalling a scene Storing a scene Checking the contents of a scene you wish to recall Check mode operation Editing and storing the scene you are checking Press the Check key once again to return to Normal mode Utility items Utility mode proceduresBasic procedure in Utility mode Program change transmission/reception OFF/on/LoC Midi channelControl change transmission/reception OFF/GrP/on Program change reception omni on/off On/oFF Control No Channel Mute group Control change table Mute group Mute groupsDirect recall About the local control cir- cuit Using mute groups Error messages General speciﬁcations Speciﬁcations Output specifications Input/output characteristicsInput specifications Included items Connector wiringOther Rear DimensionsFront Midi data format Midi Implementation Yamaha Corporation